- d&b audiotechnik
D20
The 2 RU four channel D20 amplifier is ideally suited to mobile and installation applications which require low to medium Sound Pressure Level (SPL) capabilities.
- Amplifiers
Dante-enabled Product Catalog
- Neutrik
NA-2I-DLINE
Connect your legacy audio gear to the DANTE® world. The Line I/O to DANTE® Interface is an end-of-network device. It is a breakout box which allows two channels of audio to be integrated into a DANTE® network.
- I/O Interfaces
- Dante Ch: 0x2
- 16-bit, 24-bit, 32-bit
- Neutrik
NA-2I2O-DLINE
Connect your legacy audio gear to the DANTE® world. The Line I/O to DANTE® Interface is an end-of-network device. It is a breakout box which allows two channels of audio to be integrated into a DANTE® network.
- I/O Interfaces
- Dante Ch: 2x2
- 16-bit, 24-bit, 32-bit
- Neutrik
NA-2O-DLINE
Connect your legacy audio gear to the DANTE® world. The Line I/O to DANTE® Interface is an end-of-network device. It is a breakout box which allows two channels of audio to be integrated into a DANTE® network.
- I/O Interfaces
- Dante Ch: 2x0
- 16-bit, 24-bit, 32-bit
- RCF
XPS 16KD
DANTE-EQUIPPED 4-CHANNEL DSP POWER AMPLIFIER
- 16000 W Total Continuous Power
- Dante Audio Network
- On-board Speaker Presets Library
- RDNet Networked Management
- Amplifiers
- Dante Ch: 32x32
- 32-bit
- Theory Audio Design
DLC-1500.4d
The DLC-1500.4d delivers a massive 3000W in a 16 pound chassis. Capable of delivering 1500W into 4 or 8-ohms from any channel pair, or 800W into 2 or 4-ohms all channels driven, this 16lb., 2U loudspeaker controller packs new levels of power into minimal rack space.
- Speakers
- Dante Ch: 4x4
- 24-bit
- Theory Audio Design
DLC-250.4d
Just like its predecessor (the DLC-250.4), the DLC-250.4d is small but mighty and it’s now even mightier with the addition of Dante and AES67. Capable of delivering 250W into 4, 8, and 16-ohms from any channel pair, or 125W into 4, 8 or 16-ohms all channels driven, this little 6.5lb., one-half rack loudspeaker controller packs a punch into minimal rack space.
- Speakers
- Dante Ch: 4x4
- 24-bit
- Zenty
ZT-IP400D
IP400 series encoders and decoders provide a flexible, powerful, and scalable solution at resolutions up to 3840 x 2160@60hz 4:4:4. They allow 4k UHD media to be switched and distributed over standard gigabit Ethernet networks, providing complete end-to-end streaming systems.
- AV Encoders & Decoders
- Dante AV Enabled
- Zenty
ZT-IP400E
IP400 series encoders and decoders provide a flexible, powerful, and scalable solution at resolutions up to 3840 x 2160@60hz 4:4:4. They allow 4k UHD media to be switched and distributed over standard gigabit Ethernet networks, providing complete end-to-end streaming systems.
- AV Encoders & Decoders
- Dante AV Enabled
- AMX
NMX-ENC-N2615D-WP
The AMX SVSI NMX-ENC-N2615D-WP is a cost-effective, powerfully robust encoder wallplate. It features a high-quality, low-latency 4K60 4:4:4 MWC codec that is ideal for encoding both live video and detailed content in classrooms, meeting spaces, courtrooms, bars, and other applications.
- AV Encoders & Decoders, I/O Interfaces
- Dante Ch: 2x2
- 44.1kHz-96kHz
- AMX
NMX-DEC-N2625D-WP
The AMX SVSI NMX-DEC-N2625D-WP is a cost-effective, powerfully robust decoder wallplate. It features a high-quality, low-latency 4K60 4:4:4 MWC codec that is ideal for decoding both live video and detailed content in classrooms, meeting spaces, courtrooms, bars, and other applications.
- AV Encoders & Decoders, I/O Interfaces
- Dante Ch: 2x2
- 44.1kHz-96kHz
- Wyrestorm
MX-0804-EDC
Effortlessly transition between video inputs with crystal-clear visuals. The built-in 4K60 scaler ensures a smooth, uninterrupted visual experience, making it ideal for presentations and entertainment.
- Audio Routing Matrix Switches
- Dante Ch: 4x4
- 24-bit
- Wyrestorm
MX-1007-HYB
Effortless and seamless switching for crystal-clear visuals and high-resolution content. Enhanced viewing experience with stunning detail and clarity for presentations, lectures, and entertainment, without any interruptions during source transitions.
- Audio Routing Matrix Switches
- Dante Ch: 4x4
- 24-bit
- Wyrestorm
NHD-610-TX v2
The NHD-610-TX is equipped with a 2CH Dante audio transmitter. Audio from either the HDMI or analog audio input can be sent over the network using Dante protocols for a latency free and lossless delivery to compatible audio equipment.
- AV Encoders & Decoders
- Dante AV Enabled
- AES67 Enabled
- Sennheiser
Sennheiser EW-DX EM 4 Dante
Four-channel digital full-rack (19") receiver with internal PSU and Dante® for use with Evolution Wireless Digital handheld, bodypack and tablestand transmitters. Extended 88 MHz switching bandwidth, intermodulation-free operation [intermodulation-free equidistant channel spacing] for up to 293 channels with secure AES 256 encryption and four modular network ports.
- Microphones
- Dante Ch: 0x4
- 24-bit
- Yamaha
DM3-D
The DM3-D is a compact Dante-equipped digital mixing console with versatile capabilities that make it perfect for a wide range of applications. The DM3 offers superb sound quality, fast and easy setup and operation, and professional-level features.
- Mixers
- Dante Ch: 16x16
- 24-bit, 32-bit
- Yamaha
DM7
The DM7 is a Dante-equipped versatile digital mixing console with unparalleled sound quality, ease of operation, and high reliability that make it perfect for a wide range of applications. The DM7 is configured with 24 + 4 faders and a 2 x 12” + 1 x 7” multi-touch screen.
- Mixers
- Dante Ch: 144x144
- 24-bit, 32-bit
- Blaze by Sonance
PowerZone™ Connect 2004D
The PowerZone™ Connect 2U series is a line of ultra-reliable, full-matrix DSP-enabled Class-D amplifiers that delivers exceptional system configuration and flexible output, with a total system power ranging from 1000 W to 6000 W.
- Amplifiers
- Blaze by Sonance
PowerZone™ Connect 3004D
The PowerZone™ Connect 2U series is a line of ultra-reliable, full-matrix DSP-enabled Class-D amplifiers that delivers exceptional system configuration and flexible output, with a total system power ranging from 1000 W to 6000 W.
- Amplifiers
- Blaze by Sonance
PowerZone™ Connect 122D
The PowerZone™ Connect 1U series is a line of DSP-enabled Class-D amplifiers designed to simplify the lives of system installers, providing unmatched reliability, efficiency, and exceptional system configuration.
- Amplifiers
- Blaze by Sonance
PowerZone™ Connect 504D
The PowerZone™ Connect 1U series is a line of DSP-enabled Class-D amplifiers designed to simplify the lives of system installers, providing unmatched reliability, efficiency, and exceptional system configuration.
- Amplifiers
- RDL
RU-NMP44
The RU-NMP44 is a network mixing processor containing six virtual audio mixers controlled by network commands from RDL and other network remote controls. Each mixer operates independently with input signal attenuation from unity to off. The output level from each mixer is independently adjustable from unity to off. Based on the commands sent to the RU-NMP44, each mixer can be used as a mixer, a source selector, a priority paging inserter and/or as a volume control. The outputs from four of the mixers drive corresponding network audio channels. The outputs from two of the mixers drive line-level +4 dBu audio outputs. The RU-NMP44 is configured using RDL CONSOLE or other network control software. If ducking is used, one of the four network audio inputs is assigned as the priority input. That input is connected to all six virtual mixers. An audio detector with installer-defined threshold and recovery delay may be assigned to one, several, or all of the six mixers. For each of those mixers, the priority input is set to a defined level, and the remaining three inputs are each set to attenuate to a fixed level between -10 and -64 dB when a message is detected on the priority input. If hum is anticipated from the paging source, one of four high-pass filter may be enabled. Up to four preset configurations may be stored in the RU-NMP44. Each preset can define any or all mixer level settings. A preset is activated by a network command, an RDL network or wired remote control, a momentary switch closure or a compatible open-collector from other equipment. The RU-NMP44 may be configured to power up to a preset, to the last settings used, or with all levels “off”. The RU-NMP44 may be powered from an external 24 Vdc power supply, available separately. The RU-NMP44 is equipped to operate from a PoE enabled network switch. The RU-NMP44 will reserve power from the switch even while being powered from an external 24 Vdc supply. If PoE power and an external 24 Vdc supply are both feeding an RU-NMP44, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. The RU-NMP44 is ideal for adding volume control, mixing, switching and ducking to existing network audio systems. The digital signal processing offered in the RU-NMP44 often fulfills all the requirements for an audio system design, such as in classrooms, meeting rooms, restaurants/bars, fitness gyms and retail stores. The RU-NMP44’s superior performance specifications make it ideally suited to the most demanding installations, and an exceptional value in commercial networked audio systems. The RU-NMP44 is constructed in a durable, professional all-metal enclosure suitable for free-standing, surface-mounted or rack-mounted operation. This full-featured product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. Built to last. Built to outperform.
- Mixers
- Dante Ch: 4x4
- 24-bit
- Blustream
Blustream – DA11ADE
The DA11ADE has been designed to decode a Dante® digital signal to unbalanced or balanced 2ch analogue audio.
The DA11ADE is a plug & play device that is powered using either PoE (Power over Ethernet) from any PoE network switch or via local 12v power supply input.
The DA11ADE also supports AES67 RTP audio transport and independent gain per channel for adjustment of the audio sensitivity as required.
- AV Encoders & Decoders
- Dante Ch: 2x0
- 24-bit
- Blustream
Blustream – DA11USB
The DA11USB has been designed to both encode 2ch USB audio to a Dante® digital signal, and decode a Dante® digital signal to 2ch USB audio.
The DA11USB features both USB Type-B and USB-C connections, selectable via a switch, and is a plug & play device that is powered either using PoE (Power Over Ethernet), or with 5V from the USB device. The DA11USB also supports AES67 RTP audio transport.
- AV Encoders & Decoders
- Dante Ch: 1x2
- 16-bit
- Blustream
Blustream – DA22DIG
The DA22DIG has been designed to both encode 2ch analogue or digital audio to a Dante® digital signal, and decode a Dante® digital signal to 2ch analogue and digital audio.
The DA22DIG features both analogue audio and digital audio connections, selectable via dip-switch and is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply.
The DA22DIG also features support for microphones including 48V phantom power, as well as support for AES67 RTP audio transport.
- AV Encoders & Decoders
- Dante Ch: 2x2
- 24-bit
- Blustream
Blustream – DA22XLR-WP-EU
The DA22XLR-WP is a multi-input / output wall plate to convert analogue audio within a digital Dante® networked audio system.
The DA22XLR-WP features 2 input channels of balanced / unbalanced / MIC audio with switchable 48v phantom power and 2 output channels of balanced / unbalanced audio.
The DA22XLR-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport and magnetic faceplate design allows for both UK & EU backbox compatibility.
- I/O Interfaces
- Dante Ch: 2x2
- 24-bit
- Blustream
Blustream – DA22XLR-WP-US
The DA22XLR-WP is a multi-input / output wall plate to convert analog audio within a digital Dante® networked audio system.
The DA22XLR-WP converts 2 input channels of balanced / unbalanced / MIC audio with switchable 48v Phantom power to Dante® digital audio, and 2 channels of Dante® audio to 2 output channels of balanced / unbalanced audio.
The DA22XLR-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport and magnetic faceplate design allows installation into most double-gang US junction boxes.
- I/O Interfaces
- Dante Ch: 2x2
- 24-bit