Dante-enabled Product Catalog

The Sapphire III is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. Sapphire III BASE is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. It uses the latest SSA Technology and digital audio transmission and processing technologies to create:

• PSM phase modulation technology, zero crossover distortion
• Single-stage power conversion is equivalent to the direct use of AC mains power, which is one level lower than traditional class D power amplifiers.
• Two-way energy recovery system to improve power conversion efficiency and effectively reduce the speaker coil voice temperature
• ZVS, ZCS Soft Switch Technology, Significantly Reduces Switch Heat, Further Improves Conversion Efficiency
• Overall efficiency up to 90% ultra high

In the past 100 years, the audio power amplifier topology has undergone Class-A, Class-AB, Class-D, etc., but it has always been a compromise between efficiency and sound quality. To date, SSA Technology has achieved Sapphire III BASE to Class-A sound quality levels with 90% overall system efficiency with its advanced and precise audio modulation technology, single stage power conversion, bidirectional energy recovery and soft switching technology. Really achieved "high efficiency and good voice!" Sapphire III BASE uses the latest digital audio processing and transmission technology, and targeted optimizations have been made. The efficient, reliable, and optimized application design, combined with its Class-A sound quality level, make it widely used in fixed installation systems.

The Sapphire III is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. The Sapphire III is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. It uses the latest SSA Technology and digital audio transmission and processing technologies to create:

• PSM phase modulation technology, zero crossover distortion
• Single-stage power conversion is equivalent to the direct use of AC mains power, which is one level lower than traditional class D power amplifiers.
• Two-way energy recovery system to improve power conversion efficiency and effectively reduce the speaker coil voice temperature
• ZVS, ZCS Soft Switch Technology, Significantly Reduces Switch Heat, Further Improves Conversion Efficiency
• Overall efficiency up to 90% ultra high

In the past 100 years, the audio power amplifier topology has undergone Class-A, Class-AB, Class-D, etc., but it has always been a compromise between efficiency and sound quality. Until today, SSA Technology has achieved Sapphire III's Class-A sound quality with 90% overall system efficiency with its advanced and precise audio modulation technology, single-stage power conversion, bi-directional energy recovery and soft-switching technology. Truly "efficient sound!" The application of the latest digital audio processing and transmission technology has enabled Sapphire III to achieve a new level of efficiency and sound quality. It is highly efficient, lightweight, reliable, and flexible, combined with its Class-A sound quality, making it widely used in system integration projects such as small entertainment shows and multi-purpose halls.

DSPPA's D2250 is a 2-channel amplifier. DSPPA's D2250 is a 2-channel amplifier. Features

• Comply with Dante Network System
• 2 channel amplifiers within one 1U & 19" case
• Two audio inputs, can be added to the existing Dante system
• Two priority inputs and two 100V inputs as audio sources
• 70V/100V speaker output for long distance transfer
• Industrial design for audio project, long term & stable use

DSPPA's D2125 is a 2-channel amplifier. DSPPA's D2125 is a 2-channel amplifier. Features

• 2 channel amplifiers within one 1U & 19" case
• Two audio inputs, can be added to the existing Dante system
• Two priority inputs and two 100V inputs as audio sources
• 70V/100V speaker output for long distance transfer
• Industrial design for audio project, long term & stable use

DSPPA's DT series of power amplifiers include the DT4106, DT4112, DT4125, and DT4135.  DSPPA's DT series of power amplifiers include the DT4106, DT4112, DT4125, and DT4135.  Features

• Rated power: 2x60W/2x120W/2x250W/2x350W
• Support cascaded linkage between Dante devices
• 2 AUX inputs, 2 channels speaker outputs of 70V/100
• With EMC input and activation output to volume controller
• Black & silver colors available

The AV-NH1 is a headphone amplifier that converts two Dante network audio channels to a stereo headphone output with front-panel level adjustment.  The AV-NH1 is a headphone amplifier that converts two Dante network audio channels to a stereo headphone output with front-panel level adjustment. The outputs connects through a stereo 3.5 mm Mini-jack. Each channel provides 100 mW into 100 ohms for a network digital audio level of 0 dBFS. Special software is not required to configure the module. The AV-NH1 is a professional grade product for studio quality fidelity and low noise performance. The AV-NH1 may be powered from an external 24 Vdc power supply, available separately. The AV-NH1 is equipped to operate from a PoE enabled network switch. The AV-NH1 will reserve power from the switch even while being powered from an external 24 Vdc supply. If PoE power and an external 24 Vdc supply are both feeding an AV-NH1, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. Valid power and synchronization to the Dante network is indicated by a green LED visible from the front of the unit. The AV-NH1 is constructed in a durable, professional all-metal enclosure suitable for use on stage or in studio, or mounted to any flat surface. For fixed installations, mounting brackets are included. This full-featured AV-PAK product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. Features

• Converts Two Dante Network Audio Signals to a Stereo Headphone
• Output on Professional Quality 3.5 mm stereo MINI Jack
• Selectable Dante Sample Rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
• Front-Panel Output Level Control
• Special Software Not Required for Module Setup
• Exceptional Low-Noise and Low-Distortion Performance
• High Resolution 24 Bit Digital to Analog Conversion
• Legendary RDL Analog Filtering Enhances Superb Audio Performance
• LED Indicator for Valid Power and Network Sync
• Operation from PoE Power (Class 0, IEEE 802.3af) or external 24 Vdc
• Mounts on a Microphone Stand using an RDL SF-MSM1

The SF-NP35E is an audio power amplifier that converts one Dante network audio channel to a 70 V or 100 V constant voltage amplified output.  The SF-NP35E is an audio power amplifier that converts one Dante network audio channel to a 70 V or 100 V constant voltage amplified output. The output provides 35 watts for a network digital audio level of 0 dBFS. Special software is not required to configure the module. The SF-NP35E is equipped to operate from a PoE++ enabled network switch. The SF-NP35E may be powered from an external 24 Vdc power supply, available separately. If a PoE++ powered device instantaneously demands excessive power from a PoE++ port, that port can shut off its output voltage, causing a prolonged disruption of the device operation. The SF-NP35E monitors the amplifier power and limits the current to protect the PoE++ port against shutting down even during extreme feedback or square wave modulation conditions. A red rear-panel PORT PROTECT LED flashes when the SF-NP35E reduces power consumption to prevent shutdown of the PoE++ port voltage. The SF-NP35E is equipped with an internal VCA for setting the output level. A detachable terminal block provides for the connection of an external 10 KΩ potentiometer or a 0 to 10 Vdc control voltage. The amplifier gain remains at maximum when the VCA input terminal is not connected. RDL remote controls are available to provide single-turn, multi-turn (rotary encoder) or pushbutton (ramp or fixed level selection) user level control. VCA control insures long term noise-free level adjustment. The module is equipped with both thermal and output short-circuit protection. The high-efficiency Class D output stage produces minimal heat for all levels of expected voice or music modulation. An LED MUTE indicator glows yellow when the output is muted. Valid synchronization to the Dante network is indicated by a green LED visible from the front of the unit. The SF-NP35E is constructed in a durable, professional all-metal enclosure suitable for free-standing, surface-mounted or rack-mounted operation. This full-featured SYSFLEX product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. The versatility of SYSFLEX products adds enormous flexibility in the design and installation of professional A/V systems. Features

• 35 Watts RMS Constant Voltage Amplifier
• 70 V or 100 V Output
• Converts One Dante Network Audio Signal to a Mono Constant Voltage Output
• Selectable Dante Sample Rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
• 0 dBFS Input for 35 W Output
• Automatically limits supply current to protect against PoE++ port shutdown
• VCA Control on Detachable Terminal Block
• External Control Using 10 KΩ Potentiometer or 0 to 10 Vdc
• Compatible with RDL Remote Level Controls
• Special Software Not Required for Module Setup
• LED Indicator for Network Sync
• High-Efficiency Class D Operation
• Thermal and Short-Circuit Protection
• Plenum Rated per UL 2043 Standard

The SF-NP16E is an audio power amplifier that converts one Dante network audio channel to a 70 V or 100 V constant voltage amplified output.  The SF-NP16E is an audio power amplifier that converts one Dante network audio channel to a 70 V or 100 V constant voltage amplified output. The output provides 16 watts for a network digital audio level of 0 dBFS. Special software is not required to configure the module. The SF-NP16E is equipped to operate from a PoE+ enabled network switch. The SF-NP16E may be powered from an external 24 Vdc power supply, available separately. If a PoE+ powered device instantaneously demands excessive power from a PoE+ port, that port can shut off its output voltage, causing a prolonged disruption of the device operation. The SF-NP16E monitors the amplifier power and limits the current to protect the PoE+ port against shutting down even during extreme feedback or square wave modulation conditions. A red rear-panel PORT PROTECT LED flashes when the SF-NP16E reduces power consumption to prevent shutdown of the PoE+ port voltage. The SF-NP16E is equipped with an internal VCA for setting the output level. A detachable terminal block provides for the connection of an external 10 KΩ potentiometer or a 0 to 10 Vdc control voltage. The amplifier gain remains at maximum when the VCA input terminal is not connected. RDL remote controls are available to provide single-turn, multi-turn (rotary encoder) or pushbutton (ramp or fixed level selection) user level control. VCA control insures long term noise-free level adjustment. The module is equipped with both thermal and output short-circuit protection. The high-efficiency Class D output stage produces minimal heat for all levels of expected voice or music modulation. An LED MUTE indicator glows yellow when the output is muted. Valid synchronization to the Dante network is indicated by a green LED visible from the front of the unit. The SF-NP16E is constructed in a durable, professional all-metal enclosure suitable for free-standing, surface-mounted or rack-mounted operation. This full-featured SYSFLEX product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. The versatility of SYSFLEX products adds enormous flexibility in the design and installation of professional A/V systems. Features

• 16 Watts RMS Constant Voltage Amplifier
• 70 V or 100 V Output
• Converts One Dante Network Audio Signal to a Mono Constant Voltage Output
• Selectable Dante Sample Rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
• 0 dBFS Input for 16 W Output
• Automatically limits supply current to protect against PoE+ port shutdown
• VCA Control on Detachable Terminal Block
• External Control Using 10 KΩ Potentiometer or 0 to 10 Vdc
• Compatible with RDL Remote Level Controls
• Special Software Not Required for Module Setup
• LED Indicator for Network Sync
• High-Efficiency Class D Operation
• Thermal and Short-Circuit Protection
• Plenum Rated per UL 2043 Standard

The AV-XMN4 is an interface that converts four XLR microphone inputs to Dante network audio channels.  The AV-XMN4 is an interface that converts four XLR microphone inputs to Dante network audio channels. Special software is not required to configure the AV-XMN4. Each XLR input is equipped with a switch to set the gain for dynamic or condenser microphones. A dual-LED VU meter displays the level for each input to facilitate selection of the ideal gain range. P48 phantom voltage is supplied to each microphone input. The AV-XMN4 is a professional grade product with discrete mic preamplifiers for studio quality fidelity and low noise performance. The AV-XMN4 may be powered from an external 24 Vdc power supply, available separately. The AV-XMN4 is equipped to operate from a PoE enabled network switch. The AV-XMN4 will reserve power from the switch even while being powered from an external 24 Vdc supply. If PoE power and an external 24 Vdc supply are both feeding an AV-XMN4, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. Valid power and synchronization to the Dante network is indicated by a green LED visible from the front of the unit. The AV-XMN4 is constructed in a durable, professional all-metal enclosure suitable for use on stage or in studio, or mounted to any flat surface. For fixed installations, mounting brackets are included. The chassis is designed to protect the front panel slide switches from accidental damage. This full-featured AV-PAK product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. Features

• Dante Network Interface for Four Audio Mic Inputs
• Each XLR Input Provides Switch-Selectable Mic Gain: 40 dB, 48 dB or 62 dB
• 48 V Mic Phantom (P48) on each input
• Four XLR Front-Panel Inputs
• Converts Four Standard XLR Mic Audio Sources to Dante Network Channels
• Special Software Not Required for Module Setup
• High Resolution 24 Bit Analog to Digital Conversion
• LED Indicator for Valid Power and Network Sync
• Operation from PoE Power (Class 0, IEEE 802.3af) or external 24 Vdc
• Mounts on a Microphone Stand using an RDL SF-MSM1

The PB-800-DN Industry amplifier is an ultra-reliable, high-power, 8 channel (100W per channel) audio power amplifier designed for use in critical systems.  The PB-800-DN Industry amplifier is an ultra-reliable, high-power, 8 channel (100W per channel) audio power amplifier designed for use in critical systems. It is designed to drive 100 V line loudspeaker systems and is equipped with on-board DSP allowing gain, EQ, delay and other parameters to be controlled from a remote location using WinControl software, via DANTE™. The amplifiers are fully monitored, with automatic fault detection and reporting. Inputs may be either balanced analogue audio or digital audio DANTE™. When used in conjunction with Duran Audio’s OpSTImizer® service the PB amplifiers can provide significant improvements in speech intelligibility within a tunnel.

The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems.  The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems. It is designed to drive 100 V line loudspeaker systems and is equipped with on-board DSP allowing gain, EQ, delay and other parameters to be controlled from a remote location using WinControl software, via DANTE™. The amplifiers are fully monitored, with automatic fault detection and reporting. Inputs may be either balanced analogue audio or digital audio via DANTE™. When used in conjunction with Duran Audio’s OpSTImizer® service the PB amplifiers can provide significant improvements in speech intelligibility within a tunnel.

The Duecanali 1604 is designed to work with lo-Z (from 2 Ω ) and with 70V/100V distributed lines: any mixed impedance output loads can be realized. Providing access to all functions yet easily set up, the Duecanali Series is versatile in use. Powersoft's legendary efficency saves valuable energy, keeping both operational cost and ‘carbon footprint’ at a minimum. The Duecanali 1604 is designed to work with lo-Z (from 2 Ω ) and with 70V/100V distributed lines: any mixed impedance output loads can be realized. A fully integrated state-of-the-art DSP yields extensive system management functionality. In addition to sound shaping and limiter functions in unique Powersoft style, the DSP hardware and Armonía Pro Audio Suite™ software enable compliance with IEC 60849 for the crucial requirements of sound systems for emergency purposes.

The LINUS14D is a four channel DSP, Network, Comparator and Amplifier delivering 4x 3500W of clean power in a light weight 19”/2U package. The LINUS14D is a four channel DSP, Network, Comparator and Amplifier delivering 4x 3500W of clean power in a light weight 19”/2U package. The 4 audio inputs are selectable from Analog, LiNET digital audio or DANTE audio network and are routable to any of the 4 outputs via the input matrix. LINUS14D ENGINE – the class D-IC output stage topology delivers audiophile sonic accuracy with enormous headroom providing significant improvement of the system performance in dynamics and transparency. LINUS CORE – the SHARC floating point DSP processor ensures tremendous processing power enabling the integration of sophisticated audio algorithms. The advanced signal processing includes IIR and phase linear FIR filters for perfect linearity and superior sound performance as well as advanced look-ahead and frequency dependent limiters for increased system headroom and sonic fidelity under heavy use conditions. LiNET – is a robust, redundant audio transport solution that transmits digital audio over a standard CAT5 cable. Up to 8 digital audio signals can be sent to each amplifier via LiNET, buffered and sent to the next unit via the LiNET link out for daisy chaining. The signal routing inside the LINUS14D can be done remotely or using the pushbuttons on the front panel. DANTE – transmit digital audio over an Ethernet based network. COMPARATOR – the LINUS14D provides integrated feedback loop control for sensor controlled subwoofers. The unit has four sensor inputs connected to two 5-pol Neutrik XLR input. The comparator’s electronic circuit loop measures the voice coil movement and adjusts the amplifier driving voltage and/or current to correct any driver inaccuracy. It is a closed feedback-loop and therefore self-optimizing system in which the driver confirms precisely the power it needs to produce exactly the original audio signal. The key advantage is a very extended and controlled response. Any distortion produced by the driver or the enclosure is instantly corrected by the feedback. AUX – integrated evacuation massage contact in accordance with DIN EN 60849. LINUS LIVE – Ethernet based graphical user interface for fast and flexible system configuration, tuning and control. APPLICATIONS Containing factory presets for all CODA Audio loudspeaker systems LINUS14D offers a flexible solution for touring, permanent installation, corporate AV and portable applications.

The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. As the LINUS14D is capable of powering every loudspeaker in the CODA catalogue, the M-RACK makes every smaller portable CODA system as clean and flawless in terms of aesthetics and connectivity as it is in terms of system performance. This ready-made factory solution is fully compatible with the larger LINUS-T-Rack allowing for easy cross rental and system expansion.

• One LINUS14D amplifier in a 3U case
• Delivers 4x 3500W @ 4 Ohm
• Requires only 16A / 230V (or 32A / 110V)
• Selectable inputs: Analog, AES over Ethernet, LiNET, DANTE
• Outputs on NL4, NL8
• 5-pol XLR comparator inputs for use with Coda Audio sensor controlled subwoofers
• All connectors at the front for easy workflow
• Sliding door for quick access
• Protection grill on the rear for connectors protection
• Can drive all CODA loudspeaker systems
• Fully compatible to LINUS T-RACK

Dynacord's IPX5:4 is a 4 x 1250 W multi-channel installation DSP amplifier. Dynacord's IPX5:4 is a 4 x 1250 W multi-channel installation DSP amplifier.

• 4 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX10:8 is a 8 x 1250 W multi-channel installation DSP amplifier. Dynacord's IPX10:8 is a 8 x 1250 W multi-channel installation DSP amplifier.

• 8 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier. Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier.

• 4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX20:4 is a 4 x 5000 W multi-channel installation DSP amplifier. Dynacord's IPX20:4 is a 4 x 5000 W multi-channel installation DSP amplifier.

• 4 x 5000 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel drive mode with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Monacor's AKB-30DT/DSP is a Class D mono mixing amplifier with integrated Dante® module and DSP technology. Monacor's AKB-30DT/DSP is a Class D mono mixing amplifier with integrated Dante® module and DSP technology.

• 2 x mono 15 W/4-8 Ω
• Silent operation due to fanless cooling concept
• DSP can be controlled via MONACOR DSP software or via app
• Dante® input and feed-through output
• Speaker outputs via plug-in screw terminals
• Metal housing with mounting brackets
• Power is provided via PoE (Power over Ethernet) or optional 12 V power supply

The Atlona Gain™ 120 Net (AT-GAIN-120NET) is a compact power amplifier designed for low or high impedance applications.  The Atlona Gain™ 120 Net (AT-GAIN-120NET) is a compact power amplifier designed for low or high impedance applications. A mode selector switch allows the Gain 120 Net to deliver two channels of 60 watts each into 4 or 8 ohms, or a single channel of 120 watts at 70 or 100 volts. This Class D amplifier is energy efficient and convection cooled to allow installation in conference rooms and quiet installation environments without the need for fans. The Gain 120 Net features an AES67 and Dante dual-channel audio bridge for accepting two channels over a network from a Dante or AES67-equipped DSP, as well as Atlona OmniStream™ AV encoders. In addition to the amplified speaker output, a line level audio output allows the incoming audio to be fed into an additional amplifier or audio system. The Gain 120 Net is controllable via TCP/IP or external trigger, and can be integrated with Atlona AV switchers, HDVS HDBaseT™ receivers, and OmniStream AV systems for a wide variety of sound reinforcement applications.

This amplifier platform is ideal for medium to large sized installations that require high power outputs to drive subs and multiple speakers. Duecanali 4808 DSP+D offers Powersoft’s renowned reliability and power density in a light, compact unit. This amplifier platform is ideal for medium to large sized installations that require high power outputs to drive subs and multiple speakers. Duecanali 4808 DSP+D offers Powersoft’s renowned reliability and power density in a light, compact unit. Built in state of the art DSP, in conjunction with Dante, allows flexibility during installation and extensive controllability.

Compact and light weight, it can be used as an addition to existing systems to enhance audio reproduction in small to medium sized areas. As a standalone unit, the Duecanali 804 DSP+D amplifier platform shines with outstandingly low power consumption and thermal dissipation. Compact and light weight, it can be used as an addition to existing systems to enhance audio reproduction in small to medium sized areas. As a standalone unit, the Duecanali 804 DSP+D amplifier platform shines with outstandingly low power consumption and thermal dissipation. Built in state of the art DSP, in conjunction with Dante, allows flexibility during installation and extensive controllability.

The AtlasIED High Power Amplifier “HPA” Series is designed for use in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle multiple impedance loads The AtlasIED High Power Amplifier “HPA” Series is designed for use in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle multiple impedance loads. The HPA is compact and lightweight in comparison to other models delivering similar power levels. The HPA Series features Generation II Class D Output topology that provides great efficiency with the sound quality of a Class AB amplifier. The power supply is a switch mode, global auto sensing design that maintains a stable output during fluctuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any loudspeaker load.The HPA Series features front panel detente level controls with a security cover, remote turn on, balanced inputs, fault reporting and a rear panel accessory card slot for an optional Dante™ 2-channel digital audio interface. HPA Series amplifiers feature a unique output stage, low resistance direct coupled thermal transfer design that effectively maintains optimal temperature across all loads and output levels. HPA Series amplifiers are also energy efficient and meet Energy Star standards, drawing only 1W of power in standby mode.Whether the application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the AtlasIEDHPA Series is the answer for high power/cost effective amplification needs.

The AtlasIED High Power Amplifier “HPA” Series is designed for use in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle multiple impedance loads. The AtlasIED High Power Amplifier “HPA” Series is designed for use in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle multiple impedance loads. The HPA is compact and lightweight in comparison to other models delivering similar power levels. The HPA Series features Generation II Class D Output topology that provides great efficiency with the sound quality of a Class AB amplifier. The power supply is a switch mode, global auto sensing design that maintains a stable output during fluctuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any loudspeaker load.The HPA Series features front panel detente level controls with a security cover, remote turn on, balanced inputs, fault reporting and a rear panel accessory card slot for an optional Dante™ 2-channel digital audio interface. HPA Series amplifiers feature a unique output stage, low resistance direct coupled thermal transfer design that effectively maintains optimal temperature across all loads and output levels. HPA Series amplifiers are also energy efficient and meet Energy Star standards, drawing only 1W of power in standby mode.Whether the application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the AtlasIEDHPA Series is the answer for high power/cost effective amplification needs.

The AtlasIED TitanONE T112 Smart Mainframe Power Amplifier provides the latest signal automation, processing and amplification technologies in one modular solution. The AtlasIED TitanONE T112 Smart Mainframe Power Amplifier provides the latest signal automation, processing and amplification technologies in one modular solution. The modular design allows up to seven (7) TitanONE Series power amplifier cards (sold separately) to be easily inserted into the mainframe. This offers twelve-(12) main channels of amplification and two-(2) backup channels for redundancy. Each channel has a complete library of DSP filter options. Mainframe can also be used to provide power, house and configure via software dual channel line output cards T2LD-120V-T1 two-channel line driver or T2LD-230V-T1 two-channel line driver to drive external systems, or to provide processing for self-powered loudspeaker arrays.The TitanONE T112 is networkable offeringAtlasIEDNet+ IP-based system control and digital audio transport via Dante™. TitanONE T112 integratesAtlasIED’s world-renowned SystemAssured™ Supervision for entire system monitoring and fault detection to ensure worry-free 24/7 operation. The TitanONE T112 doesn’t stop there, it also incorporates AtlasIED’s patented smart technology called AlwaysHEAR™. This ensures the audio levels are automatically adjusted to always be set at the perfect sound level. The TitanONE T112 offers over eight technologies in a single compact form factor and is the perfect solution for life safety systems and everyday installations.The T112 meets the stringent standard requirements for life safety and mass notification systems. It is recognized by UL and it can easily be incorporated into any fire or life safety system. The T112 also has the ability to enter Power-Save Mode via contact closure or over the network. In this mode, all the power amplifiers are switched off unless needed for an emergency message. This is useful to save on battery or backup power supply drain when main power is lost for example.

The new NXAMP4x1 MK2 and NXAMP4x2 MK2 present NEXO expertise in DSP control in lighter, sleeker 2U packages with front panel touch screen control enabling faster and easier navigation, and giving direct access to all essential parameters. The new NXAMP4x1 MK2 and NXAMP4x2 MK2 present NEXO expertise in DSP control in lighter, sleeker 2U packages with front panel touch screen control enabling faster and easier navigation, and giving direct access to all essential parameters including: Array EQ, Mute and Meters, EQ Detail, User EQ, Inputs, Load Monitoring, Log, Scene, Setup, System Headroom, as well as Volume, Gain and Delays. A native, dual Ethernet port offers seamless integration with NEXO proprietary NeMo system management software. Amplifiers can be remote-controlled and daisy-chained via a standard Remote Control card with optional Dante, EtherSound and AES/EBU network cards available. Four high-end analog inputs use cascaded converters for low output noise, and four digital inputs are available through the rear panel expansion card slot offering optional AES/EBU, EtherSound™, Dante™ or AES67 inputs, all with automatic analog fall-back. In addition to the expansion card slot, other rear panel connectivity includes RS232 serial and GPIO ports along with Speakon outputs for each of the four channels. Available in 4 x 1300W and 4 x 2500W @ 2 ohms and weighing in at just 35 lbs. and 36.5 lbs., respectively, the ultra-low distortion Class D amplifiers combine 32-bit/96KHz converters and 64-bit signal processing to deliver significant advances in sound quality over the already highly-regarded original NXAMPs. They feature a universal power supply (100 - 240 Volts) using PFC (Power Factor Correction) technology for maximum efficiency and smooth current draw. The NXAMP4x2 MK2 is a new design in the NXAMP range, and is ideal for the NEXO GEO Series of compact line array systems and PS Series cabinets.

The new NXAMP4x1 MK2 and NXAMP4x2 MK2 present NEXO expertise in DSP control in lighter, sleeker 2U packages with front panel touch screen control enabling faster and easier navigation, and giving direct access to all essential parameters. The new NXAMP4x1 MK2 and NXAMP4x2 MK2 present NEXO expertise in DSP control in lighter, sleeker 2U packages with front panel touch screen control enabling faster and easier navigation, and giving direct access to all essential parameters including: Array EQ, Mute and Meters, EQ Detail, User EQ, Inputs, Load Monitoring, Log, Scene, Setup, System Headroom, as well as Volume, Gain and Delays. A native, dual Ethernet port offers seamless integration with NEXO proprietary NeMo system management software. Amplifiers can be remote-controlled and daisy-chained via a standard Remote Control card with optional Dante, EtherSound and AES/EBU network cards available. Four high-end analog inputs use cascaded converters for low output noise, and four digital inputs are available through the rear panel expansion card slot offering optional AES/EBU, EtherSound™, Dante™ or AES67 inputs, all with automatic analog fall-back. In addition to the expansion card slot, other rear panel connectivity includes RS232 serial and GPIO ports along with Speakon outputs for each of the four channels. Available in 4 x 1300W and 4 x 2500W @ 2 ohms and weighing in at just 35 lbs. and 36.5 lbs., respectively, the ultra-low distortion Class D amplifiers combine 32-bit/96KHz converters and 64-bit signal processing to deliver significant advances in sound quality over the already highly-regarded original NXAMPs. They feature a universal power supply (100 - 240 Volts) using PFC (Power Factor Correction) technology for maximum efficiency and smooth current draw.