Cart
← Back to Product Catalog

Mansion – AMP-D100DI

Amplifiers

More details

Similar Products

ied-1542NA-D_600px_0|ied-1542NA-D_600px_0
  • AtlasIED

AtlasIED – IED1542NA-D

This product has reached "end-of-life" and is discontinued by the manufacturer The 1542NA-D is a compact power amplifier module capable of driving small loudspeaker loads in a GLOBALCOM® system.The 1542NA-D provides two outputs, each with 4 watts of power into an 8Ω load. This makes the module ideal for powering small zones that are made up of only a few low-powered loudspeakers.The audio inputs to the module are through the Ethernet audio network and are configured from the GLOBALCOM® System Management Center. The 1542NA-D model allows the use of Dante™ audio networking protocols.The 1542NA-D is powered using standard PoE and draw a maximum power of 13 watts. If PoE equipment is not used, an input is provided for an external +48VDC power supply. A green power indicator LED is included to show that the unit is powered on. Each channel has a green LED indicator that illuminates when signal is present and a yellow LED to indicate clipping. Another yellow LED illuminates to indicate that the device is in thermal overload. When this condition occurs, the device will stop passing signal until the condition has cleared.The amplifier is provided in an enclosure that either mounts to a DIN rail or is screwed down on a panel or wall to allow for convenient installation in remote closets close to the loudspeaker zone.Features
  • Available in single-channel or two-channel configurations
  • Available with Dante™ audio network interface
  • Control and configure using a web browser and GLOBALCOM® System Management Center
  • Settings storage in non-volatile memory
  • Full integration with theAtlasIED GLOBALCOM® vACS
  • Utilizes IEEE 802.af Power over Ethernet (PoE)
  • Removable connectors for easy installation
  • Rugged DIN-rail or panel/wall mount enclosure
    Amplifiers
See the product
  • Lake People

G103-D-4

Lake People Phone-Amp G103D4 is a headphone amplifier intended for DANTE networks. The G103D4 model comes with a DANTE 4/4 input and two independent stereo amplifiers. 24 Bit / 192 kHz D/A converters with a Signal-to-noise ratio >105 dB and THD+N as low as 0,002 % are driving the powerful headphone amplifiers. These are best suited to drive any headphones from low to high impedance and with low or high sensitivity. To adapt the amp to demanding headphones, to further reduce the noise level or to maximize the travel of the volume control, the gain is internally adaptable by Dip-Switches to optimize the amp; The DANTE digital audio signals are input via a standard RJ45 connector. Lake People G103D4 will accept 4 audio channels. The unpacked audio signals are input to two high quality D/A converters. The recovered analogue signals are buffered, attenuated in the analogue domain and then sent to powerful headphone amplifiers. If required, additional gain of +6 dB or +12 dB can be set by Dip-Switches inside the amp. Each amp section offers a 1/4” and 3.5 mm phone jack which may be used simultaneously. Power supply for the amp is accomplished either by PoE (Power-over-Ethernet) or by a USB wall plug adaptor (not supplied) with USB-B or USB-C connector. The case, front and back panel of G103D4 is made of rugged black anodized aluminum, the lettering is laser engraved. The volume knobs are also made of solid aluminum.
    Amplifiers
  • Dante Ch: 4x0
  • 24-bit
See the product
LDIPA412T_1
  • Adam Hall Group

Adam Hall – LD Systems IPA412T

Good sound belongs everywhere - in the hotel lobby, in conference rooms, in schools and houses of worship. Demands are constantly increasing, not only in terms of quality, but also in terms of flexibility. Permanently installed and still flexible? This apparent contradiction can be resolved by the IPA Series DSP-based installation amplifiers.

The IPA 412 T is a professional, four-channel installation power amplifier with 4 x 120 watts. While the 70V/100V outputs are equipped with high quality toroidal core transformers, the low impedance 4-Ohm outputs are completely transformerless and guarantee the highest possible audio quality. The versatile DSP functions include, amongst others, a parametric EQ with matching speaker library, dynamic tools, a matrix mixer, priority source selection and delay.

Despite this range of functions, the IPA Series power amps are easy to operate. Important functions such as signal, limit, protection and bridge mode are easily visible via the LEDs on the front panel.

HPF/LPF presets can be enabled directly on the device via DIP switches The IPA 412 T is already equipped for remote control using future remote panels and paging microphones from LD Systems. The back-panel slot provides expansion card connectivity for additional future-proofing. The Ethernet card offers comprehensive configuration and management via software. The Ethernet+Dante card also offers Dante audio networking capabilities and connection to a wide range of Dante-enabled devices, in order to integrate the IPA 412 T into the Dante network and resolve more complex tasks.

Times are changing; rooms are redivided or rededicated, numbers of attendees increase or decrease based on unforeseen events, but with the IPA Series DSP-supported power amps, your installation is prepared for any situation. Scalability and future-proofing are the biggest advantages of the IPA Series. Its energy efficiency is also ideal thanks to the class-D technology and switchable auto standby.

The IPA 424 T variant with 4 x 240 watts is available for larger installations.

    Amplifiers
See the product