Dante-enabled Product Catalog

The PowerZone™ Connect 2U series is a line of ultra-reliable, full-matrix DSP-enabled Class-D amplifiers that delivers exceptional system configuration and flexible output, with a total system power ranging from 1000 W to 6000 W.

The PowerZone™ Connect 1U series is a line of DSP-enabled Class-D amplifiers designed to simplify the lives of system installers, providing unmatched reliability, efficiency, and exceptional system configuration.

The PowerZone™ Connect 1U series is a line of DSP-enabled Class-D amplifiers designed to simplify the lives of system installers, providing unmatched reliability, efficiency, and exceptional system configuration.

The RU-NMP44 is a network mixing processor containing six virtual audio mixers controlled by network commands from RDL and other network remote controls. Each mixer operates independently with input signal attenuation from unity to off. The output level from each mixer is independently adjustable from unity to off. Based on the commands sent to the RU-NMP44, each mixer can be used as a mixer, a source selector, a priority paging inserter and/or as a volume control. The outputs from four of the mixers drive corresponding network audio channels. The outputs from two of the mixers drive line-level +4 dBu audio outputs. The RU-NMP44 is configured using RDL CONSOLE or other network control software. If ducking is used, one of the four network audio inputs is assigned as the priority input. That input is connected to all six virtual mixers. An audio detector with installer-defined threshold and recovery delay may be assigned to one, several, or all of the six mixers. For each of those mixers, the priority input is set to a defined level, and the remaining three inputs are each set to attenuate to a fixed level between -10 and -64 dB when a message is detected on the priority input. If hum is anticipated from the paging source, one of four high-pass filter may be enabled. Up to four preset configurations may be stored in the RU-NMP44. Each preset can define any or all mixer level settings. A preset is activated by a network command, an RDL network or wired remote control, a momentary switch closure or a compatible open-collector from other equipment. The RU-NMP44 may be configured to power up to a preset, to the last settings used, or with all levels “off”. The RU-NMP44 may be powered from an external 24 Vdc power supply, available separately. The RU-NMP44 is equipped to operate from a PoE enabled network switch. The RU-NMP44 will reserve power from the switch even while being powered from an external 24 Vdc supply. If PoE power and an external 24 Vdc supply are both feeding an RU-NMP44, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. The RU-NMP44 is ideal for adding volume control, mixing, switching and ducking to existing network audio systems. The digital signal processing offered in the RU-NMP44 often fulfills all the requirements for an audio system design, such as in classrooms, meeting rooms, restaurants/bars, fitness gyms and retail stores. The RU-NMP44’s superior performance specifications make it ideally suited to the most demanding installations, and an exceptional value in commercial networked audio systems. The RU-NMP44 is constructed in a durable, professional all-metal enclosure suitable for free-standing, surface-mounted or rack-mounted operation. This full-featured product is engineered and manufactured in the U.S.A for continuous duty in demanding installations. Built to last. Built to outperform.

The DA11ADE has been designed to decode a Dante® digital signal to unbalanced or balanced 2ch analogue audio. The DA11ADE is a plug & play device that is powered using either PoE (Power over Ethernet) from any PoE network switch or via local 12v power supply input. The DA11ADE also supports AES67 RTP audio transport and independent gain per channel for adjustment of the audio sensitivity as required.

The DA11USB has been designed to both encode 2ch USB audio to a Dante® digital signal, and decode a Dante® digital signal to 2ch USB audio. The DA11USB features both USB Type-B and USB-C connections, selectable via a switch, and is a plug & play device that is powered either using PoE (Power Over Ethernet), or with 5V from the USB device. The DA11USB also supports AES67 RTP audio transport.

The DA22DIG has been designed to both encode 2ch analogue or digital audio to a Dante® digital signal, and decode a Dante® digital signal to 2ch analogue and digital audio. The DA22DIG features both analogue audio and digital audio connections, selectable via dip-switch and is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply. The DA22DIG also features support for microphones including 48V phantom power, as well as support for AES67 RTP audio transport.

The DA22XLR-WP is a multi-input / output wall plate to convert analogue audio within a digital Dante® networked audio system. The DA22XLR-WP features 2 input channels of balanced / unbalanced / MIC audio with switchable 48v phantom power and 2 output channels of balanced / unbalanced audio. The DA22XLR-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport and magnetic faceplate design allows for both UK & EU backbox compatibility.

The DA22XLR-WP is a multi-input / output wall plate to convert analog audio within a digital Dante® networked audio system. The DA22XLR-WP converts 2 input channels of balanced / unbalanced / MIC audio with switchable 48v Phantom power to Dante® digital audio, and 2 channels of Dante® audio to 2 output channels of balanced / unbalanced audio. The DA22XLR-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport and magnetic faceplate design allows installation into most double-gang US junction boxes.

The DA44AU is a four input / four output Dante® digital audio converter. The DA44AU allows any non-Dante® audio source such as mixing consoles, amplifiers, computers and Blustream Matrix / distribution products to be connected as an audio source within a Dante® network, as well as converting a Dante® signal back to an analogue audio signal. The DA44AU supports both balanced and unbalanced audio as well as microphone line level inputs inc. 48V phantom power. The DA44AU supports AES67 RTP audio transport.

The UHD Multicast distribution platform allows virtually latency free (1 frame) distribution of HDMI video over a 1Gb Managed Network. Compatible with the current IP200 platform, the IP250UHD-RX is an industry leading 4K HDCP 2.2 HDMI video scaling receiver that, using visually lossless compression technology, delivers 10Gb HDMI, Bi-directional IR, RS-232 & USB/KVM up to lengths of 100m over standard network architecture, or greater distances using the in-built Fibre SFP port. The IP250UHD-RX features dual RJ45 network ports for independent or combined HDMI and/or Dante signal distribution. The unit can be powered via PoE from the network switch or locally should the switch not support PoE. With multiple configuration options available, the Multicast solution is ideal for both commercial and residential installations.

The UHD Multicast distribution platform allows virtually latency free (1 frame) distribution of 4K HDMI video over a 1Gb Managed Network. Compatible with the current IP200 platform, the IP250UHD-TX is an industry leading 4K HDCP 2.2 HDMI transmitter that, using visually lossless compression technology, delivers 10Gb HDMI, bi-directional IR, RS-232 & USB/KVM up to lengths of 100m over standard network architecture, or greater distances using the in-built fibre SFP port. The IP250UHD-TX features dual RJ45 network ports for independent or combined HDMI and/or Dante signal distribution. The unit can be powered via PoE from the network switch, or locally should the switch not support PoE. With multiple configuration options available, the Multicast solution is ideal for both commercial and residential installations.

The Blustream IP300 series Multicast distribution platform allows virtually latency free (1 frame) distribution of 4K HDMI video over a 1Gb managed network. Featuring full interoperability with the IP350UHD product line where Dante is required, the IP300UHD-TX is an industry leading 4K HDCP 2.2 HDMI transmitter that, using visually lossless compression technology, delivers 18Gbps HDMI, audio, bi-directional IR, RS-232 & USB/KVM up to lengths of 100m over standard copper network architecture, or greater distances using the in-built fibre SFP network interface. The unit can be powered via PoE from the network switch, or locally should the switch not support PoE. With multiple configuration options available, the flexibility of the Blustream Multicast video over IP solution makes this platform ideal for multiple installation types.

The Blustream IP300 series Multicast distribution platform allows virtually latency free (1 frame) distribution of 4K HDMI video over a 1Gb managed network. Featuring full interoperability with the IP300UHD product line, the IP350UHD-RX is an industry leading Dante enabled 4K HDCP 2.2 HDMI receiver that, using visually lossless compression technology, delivers 18Gbps HDMI, Dante & AES67 audio, bi-directional IR, RS-232 & USB/KVM up to lengths of 100m over standard copper network architecture, or greater distances using the in-built fibre SFP network interface. The IP350UHD-RX can support both video and Dante audio distribution from a single network. A second RJ45 connection allows for the Dante audio network interface to be segregated from the video over IP network if required. With a full 18Gbps HDMI scaling chipset on-board, the HDMI output can be adjusted to lower resolutions where legacy displays are required in the same system as full 4K. The scaling capabilities of this unit also allow for videowalls to be created where needed. The unit can be powered via PoE from the network switch, or locally should the switch not support PoE. With multiple configuration options available, the flexibility of the Blustream Multicast video over IP solution makes this platform ideal for multiple installation types.

The Blustream IP300 series Multicast distribution platform allows virtually latency free (1 frame) distribution of 4K HDMI video over a 1Gb managed network. Featuring full interoperability with the IP300UHD product line, the IP350UHD-TX is an industry leading Dante enabled 4K HDCP 2.2 HDMI transmitter that, using visually lossless compression technology, delivers 18Gbps HDMI, Dante & AES67 audio, bi-directional IR, RS-232 & USB/KVM up to lengths of 100m over standard copper network architecture, or greater distances using the in-built fibre SFP network interface. The IP350UHD-TX can support both video and Dante audio distribution from a single network. A second RJ45 connection allows for the Dante audio network interface to be segregated from the video over IP network if required. The unit can be powered via PoE from the network switch, or locally should the switch not support PoE. With multiple configuration options available, the flexibility of the Blustream Multicast video over IP solution makes this platform ideal for multiple installation types.

Our NPA20DA networked power amplifier delivers advanced audio integration within a commercial or residential AV installation. The NPA20DA features a 2 x 10W digital amplifier (1 x 20W mono) audio output and Dante® audio integration. The NPA20DA can be powered via PoE or PoE+ from a compatible network switch, or locally should the switch not support PoE. The unit also includes the ability to lower the amplifier power output subject to PoE capabilities, DSP with a 31 band EQ, audio delay for lip sync correction, and control via front panel, RS-232, TCP/IP, web-GUI or 12V trigger.

Our NPA70DA networked audio zone amplifier delivers advanced audio integration within a commercial or residential AV installation. The NPA70DA features a 2 x 35W digital amplifier (1 x 70W mono) or 70V / 100V hi-level constant voltage output and Dante® audio integration. The NPA70DA can be powered via PoE++ from a compatible network switch, or locally should the switch not support PoE++. The unit also includes the ability to lower the amplifier power output subject to PoE capabilities, support for combined or independent LAN and Dante® connections, DSP with a 31 band EQ, audio delay for lip sync correction, and control via front panel, IR, RS-232, TCP/IP, web-GUI or 12V trigger.

The PRO-IN4HDA board features 4x HDMI 2.0 inputs supporting 4K 60Hz 4:4:4 that can be independently routed to any HDMI/HDBaseT output board. Each HDMI input includes independent 2ch Dante audio breakout, fixed level 2ch analogue audio breakout, and 4x 2ch Dante audio inputs allowing audio embedding onto the HDMI source. The PRO-IN4HDA features quick release card module fittings allowing simple installation into the Custom Pro Matrix hub.

The DA11ABL-WP is a multi-input / output wall plate to convert Bluetooth and analogue audio within a digital Dante® networked audio system. The DA11ABL-WP converts 2 x input channels of Bluetooth, or unbalanced audio to Dante® digital audio, and 2 x channels of Dante® audio to 2 x output channels of unbalanced audio. Software configuration for the DA11ABL-WP allows for the Bluetooth name to be amended as required where being deployed in multi-user spaces. The DA11ABL-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport, and magnetic faceplate design allows for Decora backbox compatibility. The DA11ABL-WP is the ideal BYOD interface to allow any Bluetooth device to stream audio wirelessly to a Dante® audio system.

The DA11ABL-WP-US is a multi-input / output wall plate to convert Bluetooth and analog audio within a digital Dante® networked audio system. The DA11ABL-WP converts 2 x input channels of Bluetooth, or unbalanced audio to Dante® digital audio, and 2 x channels of Dante® audio to 2 x output channels of unbalanced audio. Software configuration for the DA11ABL-WP allows for the Bluetooth name to be amended as required where being deployed in multi-user spaces. The DA11ABL-WP is a plug & play device that is powered using PoE (Power over Ethernet), or via 12V power supply, offers support for AES67 RTP audio transport, and magnetic faceplate design allows for both UK & EU backbox compatibility. The DA11ABL-WP is the ideal BYOD interface to allow any Bluetooth device to stream audio wirelessly to a Dante® audio system.

PRAGMA BTone Dante 2 is a high-quality advanced Bluetooth® Audio Interface for reliable operation in fitness studios, hotels, restaurants, churches, schools, meeting rooms and other locations. API, individual naming, 2x2/4x2 or 4x4 Audio, Bluetooth 5.0, visibility options, simple or PIN-code pairing, black/white/aluminum (US)

Rack-mounted Media Station that supports mixing, recording, streaming, and backing up video from up to 4 Full HD or 2 4K sources simultaneously. Features:

• Up to 2160p30 recording and streaming.
• Up to 2 RTMP/RTMPS streams to any CDN.
• Includes NDI|HX and Dante Audio licences.
• 2 TB internal HDD.
• VCMS integrations (Opencast, Kaltura, Panopto), FTP/SFTP and Google Drive support.
• Built-in web interfaces for real time control of the recording and streaming processes and for video managing.
• Different ways to control: mobile phone, Graphical User Interface (GUI), Online Director web page and app (Windows/Mac), RS-232/TCP, USB numeric keypad, Cloud, and API for a deeper integration.
• Package additionally contains rack mounts and a USB numeric keypad.

Bolin’s D20 Series Dante AV Ultra transceiver device can be programmed as an encoder or a decoder via firmware update. D20 Series is a single channel networked AV over IP transceiver that is fully compatible with Dante audio devices within a Dante ecosystem for HDMI sources up to 4K60Hz 4096 x 2160, with embedded audio and PTZ camera movement control via IP or IR pass-through. It provides audio and video streaming over a standard gigabit network and D20S/D20H models as decoders output baseband video, either HDMI or 12G SDI, to work in professional AV applications. D20S has HDMI 2.0 and 12G-SDI output, which has SDI video processor built-in to provide SDI (Up to 12G-SDI) signal decode for Pro AV and broadcast video workflow applications.

1CH HDMI2.0 4KP60 Encoder/Decoder The SC6F0N1 HDMI 2.0 Pro supports 1 channel of Dante AV-H video encoder or decode with 4Kp60 resolution. Dante AV-H requires only 100Mbps bandwidth and less than 100ms video transmission delay, which is ideal for intelligent education and webcasting. YUAN ODM’s AV-over-IP solutions that are designed to support various video and audio transmission protocols. You can find solutions for different input interfaces and number of channels. All product lines are supported with a same SDK package.

1CH HDMI2.0 4KP60 Encoder/Decoder The SC6F0N1 HDMI 2.0+ supports 1 channel of Dante AV-H video encoder or decode with 4Kp60 resolution. Dante AV-H requires only 100Mbps bandwidth and less than 100ms video transmission delay, which is ideal for intelligent education and webcasting. YUAN ODM’s AV-over-IP solutions that are designed to support various video and audio transmission protocols. You can find solutions for different input interfaces and number of channels. All product lines are supported with a same SDK package.

1CH HDMI 1080P60 Encoder The SC6E0N1 HDMI to IP/UVC v2 allows you to encode one channel of video from an HDMI source to Dante AV-H at 1080p60 resolution. Dante AV-H requires only 100Mbps bandwidth and less than 100ms video transmission delay, which is ideal for intelligent education and webcasting. YUAN ODM’s AV-over-IP solutions that are designed to support various video and audio transmission protocols. You can find solutions for different input interfaces and number of channels. All product lines are supported with a same SDK package.

1CH SDI+HDMI 1080P60 ENCODER+DECODER The SC6E0N1 AIO supports 1 channel of Dante AV-H video encode or decode with 1080p60 resolution. Dante AV-H requires only 100Mbps bandwidth and less than 100ms video transmission delay, which is ideal for intelligent education and webcasting. YUAN ODM’s AV-over-IP solutions that are designed to support various video and audio transmission protocols. You can find solutions for different input interfaces and number of channels. All product lines are supported with a same SDK package.