Dante-enabled Product Catalog

The HPA-DAC2 is a Dante™ network audio card for use with high power HPA series amplifiers The HPA-DAC2 is a Dante™ network audio card for use with high power HPA series amplifiers.Compatible with:

• HPA2602 high power HPA series amplifier
• HPA4202 high power HPA series amplifier

The 5401CS is a push-to-talk switch only digital microphone station. It is a network appliance with a unique IP address that requires no configuration.  Just likeAtlasIED’s other digital microphone stations, the 5401CS uses a single Ethernet interface for audio and control data.  The 5401CS is fully compatible with IEEE 802.3af standard for Power over Ethernet (PoE), allowing the microphone station to be powered directly from any standard off-the-shelf PoE switch.The 5401CS utilizes Dante™ technology for transporting high-quality, low-latency digital audio over Ethernet. The 5401CS microphone station may be used as part of an EN54-16 listed life safety system; although the mic stations themselves are not EN 54-16 listed and cannot be used for the emergency locations.  Instead, in a dual-use system, these microphone stations may be used for everyday paging functions.

TheAtlasIED5404CS digital microphone station is a 4-button device for initiating audio / visual announcements, messages and pages with the 5400ACS Announcement Control Systems. Just likeAtlasIED’s other digital microphone stations, the 5404CS uses a single Ethernet interface for audio and control data.  The 5404CS is fully compatible with IEEE 802.3af standard for Power over Ethernet (PoE), allowing the microphone station to be powered directly from any standard off-the-shelf PoE switch.The 5404CS utilizes Dante™ technology for transporting high-quality, low-latency digital audio over Ethernet. The 5404CS microphone station may be used as part of an EN54-16 listed life safety system; although the mic stations themselves are not EN 54-16 listed and cannot be used for the emergency locations.  Instead, in a dual-use system, these microphone stations may be used for everyday paging functions.

The DNA2404DL amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The DNA2404DL amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The amplifier features Audinate's Dante™ digital audio input and four channels of 600 watt amplification. The DNA2404DL is controlled with network commands for selecting input routing and configuring EQ, delay and output levels. Amplifiers may be controlled by a stand-alone GLOBALCOM® configuration utility or through the GLOBALCOM System Management Center.The internal amplifier cards are Class D (switching mode) dual channel 600W amplifiers into the rated loads (70.7 Volts into 8Ω). Class D operation, combined with an integral switching mode power supply, offers many advantages, and the uniqueAtlasIED design makes full use of these benefits. They include higher efficiency, increased reliability, improved performance, and lower operating cost. Switching mode operation combined with high voltage power MOSFET devices make it possible to eliminate the heavy, costly, bulky transformers.AtlasIED’s design is stable under all load conditions (phase angles of 0 to 360 degrees). The amplifier card has 34dB of gain from its analog input to the loudspeaker output. Attenuation is handled ahead of the power amplifier by DSP controls through software.

The DNA2404DH amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The DNA2404DH amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The amplifier features Audinate's Dante™ digital audio input and four channels of 600 watt amplification. The DNA2404DH is controlled with network commands for selecting input routing and configuring EQ, delay and output levels. Amplifiers may be controlled by a stand-alone GLOBALCOM® configuration utility or through the GLOBALCOM System Management Center.The internal amplifier cards are Class D (switching mode) dual channel 600W amplifiers into the rated loads (100-Volts into 16Ω). Class D operation, combined with an integral switching mode power supply, offers many advantages, and the uniqueAtlasIED design makes full use of these benefits. They include higher efficiency, increased reliability, improved performance, and lower operating cost. Switching mode operation combined with high voltage power MOSFET devices make it possible to eliminate the heavy, costly, bulky transformers.AtlasIED’s design is stable under all load conditions (phase angles of 0 to 360 degrees). The amplifier card has 34dB of gain from its analog input to the loudspeaker output. Attenuation is handled ahead of the power amplifier by DSP controls through software.

This product has reached "end-of-life" and is discontinued by the manufacturer The 1581NA-D is a compact power amplifier module capable of driving small loudspeaker loads in a GLOBALCOM® system. It provides a single output with 8 watts of power into an 8Ω load.The audio inputs to the module are through the Ethernet audio network and are configured from the GLOBALCOM® System Management Center. The 1581NA-D model allows the use of Dante™ audio networking protocols.The 1581NA-D is powered using standard PoE and draw a maximum power of 13 watts. If PoE equipment is not used, an input is provided for an external +48VDC power supply. A green power indicator LED is included to show that the unit is powered on. Each channel has a green LED indicator that illuminates when signal is present and a yellow LED to indicate clipping. Another yellow LED illuminates to indicate that the device is in thermal overload. When this condition occurs, the device will stop passing signal until the condition has cleared.The amplifier is provided in an enclosure that either mounts to a DIN rail or is screwed down on a panel or wall to allow for convenient installation in remote closets close to the loudspeaker zone.Features

• Available in single-channel or two-channel configurations
• Available with Dante™ audio network interface
• Control and configure using a web browser and GLOBALCOM® System Management Center
• Settings storage in non-volatile memory
• Full integration with theAtlasIED GLOBALCOM® vACS
• Utilizes IEEE 802.af Power over Ethernet (PoE)
• Removable connectors for easy installation
• Rugged DIN-rail or panel/wall mount enclosure

This product has reached "end-of-life" and is discontinued by the manufacturer The 1542NA-D is a compact power amplifier module capable of driving small loudspeaker loads in a GLOBALCOM® system.The 1542NA-D provides two outputs, each with 4 watts of power into an 8Ω load. This makes the module ideal for powering small zones that are made up of only a few low-powered loudspeakers.The audio inputs to the module are through the Ethernet audio network and are configured from the GLOBALCOM® System Management Center. The 1542NA-D model allows the use of Dante™ audio networking protocols.The 1542NA-D is powered using standard PoE and draw a maximum power of 13 watts. If PoE equipment is not used, an input is provided for an external +48VDC power supply. A green power indicator LED is included to show that the unit is powered on. Each channel has a green LED indicator that illuminates when signal is present and a yellow LED to indicate clipping. Another yellow LED illuminates to indicate that the device is in thermal overload. When this condition occurs, the device will stop passing signal until the condition has cleared.The amplifier is provided in an enclosure that either mounts to a DIN rail or is screwed down on a panel or wall to allow for convenient installation in remote closets close to the loudspeaker zone.Features

• Available in single-channel or two-channel configurations
• Available with Dante™ audio network interface
• Control and configure using a web browser and GLOBALCOM® System Management Center
• Settings storage in non-volatile memory
• Full integration with theAtlasIED GLOBALCOM® vACS
• Utilizes IEEE 802.af Power over Ethernet (PoE)
• Removable connectors for easy installation
• Rugged DIN-rail or panel/wall mount enclosure

The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The HPA is compact and lightweight in comparison to other models delivering the similar power levels. The HPA Series features generation II Class I Output topology that gives the efficiency close to a Class D amplifier with the sound quality of a Class AB amplifier. The power supply is switch mode global auto sensing gen 3 design that maintains a stable output during fluxuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage andcurrent to virtually any speaker load.The HPA Series features front panel detented level controls with a security cover, remote turn on, balanced inputs, fault reporting and an accessory card slot for an optional Dante™ 2-channel digital audio interface. Cooling is not an issue because of the unique output stage low resistance direct couple thermal transfer design. HPA also is energy efficient and meets Energy Starr standards with only drawing 1W of power in standby mode.Whether your application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the Atlas Sound HPA Series is the answer for high power/cost effective amplification needFeatures

• 70.7V/100V and 2Ω, 4Ω, and 8Ω Output Configurable
• Balanced Inputs Euro Block Phoenix Style Connector
• High Efficiency Fan Cooling
• Remote Turn On
• Accessory Card Slot for Optional Dante™ Digital Network Audio Card
• Short-Circuit, Temperature, and DC Offset Protection
• Soft Clip Limiter Protection
• Stepped Attenuators with Security Covers
• Stereo, Bridge, or Parallel Operating Modes Selectable via Rear Mounted Switch
• Auto Sensing 120V/220V AC Mains Power Supply
• Meets Energy Star Standards - 1W Standby Mode

The BlueBridge® BB-168AECDT DSP audio processor with Acoustic Echo Cancellation and Dante™ is a powerful and flexible tool offering mission critical solutions to successfully satisfy your customers’ teleconferencing and video conferencing needs. The BlueBridge® BB-168AECDT DSP audio processor with Acoustic Echo Cancellation and Dante™ is a powerful and flexible tool offering mission critical solutions to successfully satisfy your customers’ teleconferencing and video conferencing needs. Engineered to strict standards with the highest quality internal components, BlueBridge® DSP solutions provide pure clean analog and digital audio, Ethernet connectivity for cost effective TCP/IP control and open architecture with Drag and Drop programmability.  Atlas Sound offers the widest range of open architecture DSP platform I/O configurations of any manufacturer in the industry, all configured using the same software.The BlueBridge® AEC model with the Dante™ digital audio network chipset offers up to 16 channels of self-configuring, true plug-and-play digital audio over an Ethernet network providing the highest quality audio over existing network infrastructure.Features

• Wide-Band Acoustic Echo Cancellation
• Dante™ Ethernet Based Digital Audio
• True Plug-and-Play Digital Audio Networking
• 16x8 I/O Configuration
• Open Architecture Programmability
• High Quality THAT® Corporation Mic Preamps
• TCP/IP Third Party Control Capability
• Four Logic Inputs & Outputs
• 48KHz, 40 Bit Floating DSP Engine
• Remote Control Using Optional Wall Plates
• Output Peak & Signal Indicator LEDs
• Safety Listed to UL60005

The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The HPA is compact and lightweight in comparison to other models delivering the similar power levels. The HPA Series features generation II Class I Output topology that gives the efficiency close to a Class D amplifier with the sound quality of a Class AB amplifier. The power supply is switch mode global auto sensing gen 3 design that maintains a stable output during fluxuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any speaker load.The HPA Series features front panel detented level controls with a security cover, remote turn on, balanced inputs, fault reporting and an accessory card slot for an optional Dante™ 2-channel digital audio interface. Cooling is not an issue because of the unique output stage low resistance direct couple thermal transfer design. HPA also is energy efficient and meets Energy Starr standards with only drawing 1W of power in standby mode.Whether your application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the Atlas Sound HPA Series is the answer for high power/cost effective amplification needFeatures

• 70.7V and 2Ω, 4Ω, and 8Ω Output Configurable
• Balanced Inputs Euro Block Phoenix Style Connector
• High Efficiency Fan Cooling
• Remote Turn On
• Accessory Card Slot for Optional Dante™ Digital Network Audio Card
• Short-Circuit, Temperature, and DC Offset Protection
• Soft Clip Limiter Protection
• Stepped Attenuators with Security Covers
• Stereo, Bridge, or Parallel Operating Modes Selectable via Rear Mounted Switch
• Auto Sensing 120V/220V AC Mains Power Supply
• Meets Energy Star Standards - 1W Standby Mode

The 5400ACS is an integrated announcement controller with built-in message server capability that is the core of an EN 54-16 compliance life/safety emergency notification system. These units contain all of the intelligence to manage an entire system of emergency communication stations, digital zone manager amplifier units, and other network peripherals. The 5400ACS manages the system in compliance with the EN 54-16 standard, performing overall supervision and reporting of equipment faults plus any ongoing alarm conditions.  The 5400ACS is capable of interfacing with GLOBALCOM 1100ACS/1200ACS units when additional non-emergency features or additional peripherals are required in an installation.Announcement Management Features

• Can handle dynamic requests for live pages, delayed pages, Digital Record and Playback (DRP), prerecorded messages (simple and assembled), and mute actions.
• Internal message server capable of recording 2 channels of delayed messages while providing 2 channels of message playback; all occur simultaneously in addition to as many live pages that can be supported by Dante on the network.
• Manages disabled and delayed zones.
• Network audio using Dante (High Quality Audio over Ethernet).
• Announcements can be initiated by contact closures, from a microphone paging station, from the 5400ACS front panel, or by a network command from higher level management software such asAtlasIED Director.
• Messages can be played based on schedules.
• Fully monitors and supervises all components of the system.
• Fully customizable and programmable via software tools.

Device Interface/Management Features

• Provides 8 optically isolated logic inputs for external interfaces including supervision of logic links.
• Provides 4 Form C relay outputs for external interfaces.
• Multiple controllers can be used together to create larger systems.
• Provides two analog audio inputs for such sources as background music or fire panel audio.
• Provides two analog audio outputs for audio monitor or zone outputs.
• Manages up to 50 digital microphone stations (5416CS H/G or 5450CS H/G Series) on one 5400ACS.
• Supervises all associated devices and provides fault status information.
• Overall Form C fault relay provided.
• Works seamlessly withAtlasIED5400LL Lifeline Controllers providing hot-standby and individual fail-over support.
• Interfacing DZMs can allow management for up to 1024 individual zones.(5404DZM/5432DZM).
• Provides redundant ethernet ports.

Message Server Features

• Stores up to 250 hours of pre-recorded .wav message files.
• Delayed messages limited only by disk space.
• Capable of 2 playback and 2 recording operations simultaneously.

The BB-EB1616DT can be incorporated into any BlueBridge system as an I/O expander or it can be used as a standalone digital snake on networks featuring Dante™.

The BB-1616DT is a BlueBridge DSP audio processor featuring a 16 Input and 16 Output configuration with Dante™ that features powerful and flexible tools offering mission critical solutions to satisfy the exact needs of any installation.

The BB-816DT is a BlueBridge DSP audio processor featuring a 8 Input and 16 Output configuration with Dante™ that features powerful and flexible tools offering mission critical solutions to satisfy the exact needs of any installation.

The BB-168DT is a BlueBridge DSP audio processor featuring a 16 Input and 8 Output configuration with Dante™ that features powerful and flexible tools offering mission critical solutions to satisfy the exact needs of any installation.

The BB-88DT is a BlueBridge DSP audio processor featuring a 8 Input and 8 Output configuration with Dante™ that features powerful and flexible tools offering mission critical solutions to satisfy the exact needs of any installation.