Dante-enabled Product Catalog

Designed for audio or video conferencing, the C303W-D offers consultants and designers a new option when specifying hanging microphones in applications that demand the highest sound quality. The C303W-D uses the same tri-element microphone array, covering a 360 degree pick up pattern, but packaged in a Dante/AES67 version. Each independent capsule is RF immune, will capture approximately 120 degrees and is optimized for speech intelligibility. Its three channel, Dante transporter is powered by Power over Ethernet. It features an RGB LED ring on its ceiling rose (grommet) for mute status confirmation at a glance. It ships in a plenum rated enclosure for North-America. It does not require phantom power as it outputs on the Dante network.

• Contains 3 high sensitivity cardioid capsules.
• Designed to capture 360 degree pickup.
• Engineered in high quality brass.
• Include ceiling enclosure with locking grommet for easy height adjustment.
• Supplied with 2.5 Metre cable terminating in a Tini Q connector.
• Finished in Satin Black or gloss white finish.
• RJ45 out allows fast connection to DSP or mixer.
• Supplied with RJ45 to phoenix link cable.
• 3 X Cardioid Patterns, 120° from each other, covering 360°

The Bose® ControlSpace® ESP-1240AD engineered sound processor is an open-architecture DSP with 12x4 fixed analog audio, built-in 8-channel ESPLink output and a rear-panel digital expansion slot offering IP-based network audio and control card options.  The Bose® ControlSpace® ESP-1240AD engineered sound processor is an open-architecture DSP with 12x4 fixed analog audio, built-in 8-channel ESPLink output and a rear-panel digital expansion slot offering IP-based network audio and control card options. This model meets today’s strict requirements for high-quality signal processing and control in a cost-effective package. The ESP-1240AD is designed for a wide variety of applications ranging from small self-contained projects to larger networked applications.

• High-quality analog circuitry offers both mic and line-level I/O, operates with ultra-low noise and 115 dB dynamic range
• Advanced digital signal processing supports audio at 48 kHz sample rate/24-bit, uses a floating-point open architecture DSP and operates at low latencies for sound system precision
• Expansion card slot supports the use of accessory networking cards, allowing digital audio to be sent and/or received from other compatible products
• 32x32 Dante audio networking
• Bose® ControlSpace® Designer™ software enables a large set of signal processing modules, such as automatic mic mixing, multiband graphic and parametric EQs, Bose loudspeaker libraries, signal generators, routers, mixers, AGCs, duckers, gates, compressors, source selectors and delays
• Front panel RJ-45 Ethernet connection enables localized configuration and monitoring, while enabling network passthrough when using a rear-panel network option card
• Built-in Bose ESPLink output sends up to 8 channels of uncompressed digital audio to ESPLink-equipped Bose PowerMatch® amplifiers
• A variety of control options – ControlSpace ESP products are compatible with the programmable Bose CC-64 and CC-16 controllers and three simplified zone volume interfaces, as well as potentiometers and switches built by other manufacturers
• Integration with industry-standard control systems using a comprehensive serial protocol through onboard RS-232 and Ethernet ports

The Bose® ControlSpace® ESP-880AD engineered sound processor is an open-architecture DSP with 8x8 fixed analog audio, built-in 8-channel ESPLink output and a rear-panel digital expansion slot offering IP-based network audio and control card options. The Bose® ControlSpace® ESP-880AD engineered sound processor is an open-architecture DSP with 8x8 fixed analog audio, built-in 8-channel ESPLink output and a rear-panel digital expansion slot offering IP-based network audio and control card options. This model meets today's strict requirements for high-quality signal processing and control in a cost-effective package. The ESP-880AD is designed for a wide variety of applications ranging from small self-contained projects to larger networked applications.

• High-quality analog circuitry offers both mic and line-level I/O, operates with ultra-low noise and 115 dB dynamic range
• Advanced digital signal processing supports audio at 48 kHz sample rate/24-bit, uses a floating-point open architecture DSP and operates at low latencies for sound system precision
• Expansion card slot supports the use of accessory networking cards, allowing digital audio to be sent and/or received from other compatible products
• 32x32 Dante audio networking
• Bose® ControlSpace® Designer™ software enables a large set of signal processing modules, such as automatic mic mixing, multiband graphic and parametric EQs, Bose loudspeaker libraries, signal generators, routers, mixers, AGCs, duckers, gates, compressors, source selectors and delays
• Front panel RJ-45 Ethernet connection enables localized configuration and monitoring, while enabling network passthrough when using a rear-panel network option card
• Built-in Bose ESPLink output sends up to 8 channels of uncompressed digital audio to ESPLink-equipped Bose PowerMatch® amplifiers
• A variety of control options – ControlSpace ESP products are compatible with the programmable Bose CC-64 and CC-16 controllers and three simplified zone volume interfaces, as well as potentiometers and switches built by other manufacturers
• Integration with industry-standard control systems using a comprehensive serial protocol through onboard RS-232 and Ethernet ports

The M3 is an innovative, tri-element hanging ceiling microphone designed for applications where aesthetics, sound quality, and ease of installation are critical. The M3 is an ideal audio capture solution for video conferencing, distance learning, courtroom activities, and surgical procedures. It can also be used for ambient room miking and surveillance. The M3 ceiling microphone incorporates three phase coherent hypercardioid capsules with tailored frequency response optimized for speech intelligibility. This is accomplished by minimizing frequencies caused by noise, vibration, paper shuffling, keyboard strokes, fans, and heating /air conditioning. Low noise preamp circuitry is employed for highest possible signal to noise and studio quality sound. A high-quality silicone jacketed microphone cable ensures a balanced, shielded signal and a very clean look. Electronics above the ceiling are housed within a plenum rated junction box and cable connections are made via an RJ45 connector embedded within a proprietary brass housing for an airtight seal. The M3 installed ceiling microphone connects to the input of a mixer or dsp console via a breakout cable (provided). The breakout cable consists of a female RJ45 connector that terminates in either three terminal block or XLR connectors. A variety of optional shielded CAT7 cable lengths (from plenum rated junction box to break out cable) are available. Installing the M3 requires drilling just one 5/8-inch hole in the ceiling, with no additional tools needed. The M3 mounting hardware easily adjusts the cable hanging height up to four feet from the ceiling surface without removing ceiling tiles. A wire safety cable provides additional seismic restraint. Features

• 100% RF shielding and immunity
• Gold diaphragm condenser capsules with studio quality sound
• Low impedance design allows for extremely long cable runs (if required) without cross talk or interference
• Frequency and pattern tailored for voice clarity and rejection of extraneous noise
• Evenly dispersed sound with undetectable phase
• High-quality silicone jacketed microphone cable with adjustable length and position
• Plenum rated junction box with RJ45 connector
• All visible components of the microphone and cable are same color: charcoal or white
• TAA compliant
• Very high output, low self-noise
• Easy to install

The massive weight & tone of classic Rupert Neve Designs studio microphone preamps: now available for the stage. With mastering-grade 24-bit 192kHz converters and full Dante integration, the RMP-D8 finally offers the live sound world something that studios have always coveted: the sound of Rupert Neve Designs. The heart of the RMP-D8 lies in the modular mic preamp cards. Unlike other designs that rely primarily on a single IC for gain & tone, each channel on the RMP-D8 has a fully-realized class-A microphone preamplifier feeding a custom-built Rupert Neve Designs transformer. Coupled with 24-bit/192kHz converters with precision­-controlled internal clocking and enhanced jitter reduction, there is no weak link in the audio path, thus maintaining the high standards of Rupert Neve Designs' standalone preamplifiers. From concert halls to arenas, clubs, studios, houses of worship, and educational facilities, the RMP-D8 brings the classic sound of Rupert Neve Designs into the Dante-connected world.

The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 8.8M provides 8x8 balanced analog audio inputs and outputs. The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 8.8M provides 8x8 balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a gain range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu. RGB LEDs on the Iyo’s front panel show per channel audio levels and streaming status. The Iyo family feature an embedded web server, allowing configuration and monitoring of input and output levels. Routing is achieved using the Dante Controller. Power is provided from a built-in universal AC power supply. Redundant power is available using an external 12VDC supply via a locking 2.1mm jack. All units can also be operated in AES67 interoperability mode.

The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 16.16M provides 16x16 balanced analog audio inputs and outputs. The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 16.16M provides 16x16 balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a gain range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu. RGB LEDs on the Iyo’s front panel show per channel audio levels and streaming status. The Iyo family feature an embedded web server, allowing configuration and monitoring of input and output levels. Routing is achieved using the Dante Controller. Power is provided from a built-in universal AC power supply. Redundant power is available using an external 12VDC supply via a locking 2.1mm jack. All units can also be operated in AES67 interoperability mode.

The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 32.32M provides 32x32 balanced analog audio inputs and outputs. The Iyo Dante® is a cost-effective family of microphone/line Dante audio-over-IP (AoIP) interfaces in a 1U rack mount format. The 32.32M provides 32x32 balanced analog audio inputs and outputs. Each input accommodates microphone through line level signals with a gain range of -60 to +24dBu. +48V phantom power is individually switchable on each input. Output levels are configurable up to +24dBu. RGB LEDs on the Iyo’s front panel show per channel audio levels and streaming status. The Iyo family feature an embedded web server, allowing configuration and monitoring of input and output levels. Routing is achieved using the Dante Controller. Power is provided from a built-in universal AC power supply. Redundant power is available using an external 12VDC supply via a locking 2.1mm jack. All units can also be operated in AES67 interoperability mode.

The VXL1B-16P (black) and VXL1W-16P (white) support the "Dante" audio network, and use a slim line-array configuration, making them an easy fit perfectly for conference rooms (in the size range of 12m × 10m) that demand vocal clarity while imposing numerous constraints on space, and require both functionality and a sense of design. The VXL1B-16P (black) and VXL1W-16P (white) support the "Dante" audio network, and use a slim line-array configuration, making them an easy fit perfectly for conference rooms (in the size range of 12m × 10m) that demand vocal clarity while imposing numerous constraints on space, and require both functionality and a sense of design. With audio distributed via a Dante network and PoE power* supplied from a PoE compliant L2 switch, the speaker system can be constructed as a network, allowing existing IT infrastructure to be effectively utilized. Simple wiring via LAN cables, easy installation, and no need for a power amp contribute to the flexibility of installation, allowing you to construct an elegant sound system that will not interfere with the design of the conference room.

The HY144-D-SRC audio interface card supports the Dante audio network protocol, handling up to 144 input and 144 output channels of 96 kHz/32-bit digital audio. The HY144-D-SRC audio interface card supports the Dante audio network protocol, handling up to 144 input and 144 output channels of 96 kHz/32-bit digital audio. Onboard sample rate conversion allows interconnection between devices operating at different sampling rates. Five operational modes can be selected via firmware.

• Transmits and receives up to 144 input and 144 output channels of uncompressed 96 kHz/32-bit digital audio.
• Primary and secondary connectors support redundant connections. Daisy chain connections also supported.
• Five firmware-selectable operating modes: 144io (SRC off, 144 in/144 out), 144io SyncSRC (SRC on, synchronous, 144 in/144 out), 72io AsyncSRC (SRC on, asynchronous, 72 in/72 out), 144in AsyncSRC (SRC on, asynchronous, 144 in/0 out), 144o AsyncSRC (SRC on, asynchronous, 0 in/144 out).
• Dimensions (W x H x D): 125 x 37 x 207mm (4.9" x 1.5" x 8.2")
• Net Weight: 0.25 kg (0.6 lbs)

Complex network switch setup that was previously better left to an IT technician can now be easily accomplished by anyone. A simple switch setting is all it takes to optimize SWP1 series network switches for Dante operation, and a dedicated Windows application provides “network visibility” for comprehensive monitoring and control. The "SWR2311P-10G" is an intelligent L2 switch that provides the ideal functionality for the "Dante" digital audio network that was developed by the Audinate Corporation and is now used world-wide, allowing construction of a stable network that simplifies settings, monitoring, management, and operation. When you connect the VXL1-16P to the SWR2311P-10G, optimal settings for Dante are made automatically via LLDP that is a protocol for passing system management data between a device and its neighboring device. PoE compliant ports can supply a maximum of 30W for all ports simultaneously. It can power not only PoE compliant devices such as the "MCP1" wall-mount controller used for controlling the volume of sound equipment used in conference rooms, or wireless access points, and can also provide ample power for driving even devices that require higher-output PoE such as the VXL1B-16P or VXL1W-16P.

The DCU304 is a Dante enabled Commentary / Announcer unit. It has four inputs, one programme output and three talkback outputs.  The DCU304 is a Dante enabled Commentary / Announcer unit. The unit has four inputs, each selectable to left/right/both ears, one programme microphone output plus three 'lazy' talkback outputs. On pressing a talkback key the programme microphone output will be silently muted and redirected to the selected talkback output(s). The microphone also has a local line level analogue output which also mutes when a talkback key is pressed. Network connection may be either a Neutrik ethercon or a standard RJ45 connector. A LED indicates network status. Microphone gain is adjustable in 1dB steps from +70dB to +15dB and +5dB via the OLED display and lockable push buttons. 48 volt phantom power may also be selected. The DCU304 may be powered PoE or via an external 12 volt power source. The DCU304 can also be used as a cost effective Dante four wire box or as a top quality analogue or Dante mic amp.

DSPPA's DT4T4100E is a wall mount speaker with Dante autio networking. DSPPA's DT4T4100E is a wall mount speaker with Dante autio networking. Features

•  Comply with Dante Network System
• Built-in 2x25W/2x50W digital amplifier
• Can play music, paging and alarm from the console
• One AUX input, one AUX output, 100V input
• 1 AUX output of RCA for power extension
• LED screen indicator for display status

The DARK1616S adds to Glensound's DARK series of professional network Audio I/O devices. The DARK1616S adds to the Glensound's DARK series of professional network Audio I/O devices. The whole Dark series features Redundant Power Supplies and Redundant Networking with both Redundant copper and fiber network circuits available. It was designed for 24/7/365 working in on-air environments. It provides 16 analogue audio inputs or 8 AES3 inputs to the Dante network. It also provides 16 analogue outputs from the network which are in parallel with 8 AES3 outputs. The 'S' part of the product name denotes synchronization, whereby a Word clock input can be used to synchronize the AES3 outputs. It also features a Word clock output that is clocked at the Dante network clock rate which can be used to lock external studio equipment to.

The AoIP22 is designed to easily and quickly interface existing analogue equipment to a Dante® / AES67 network audio system. Packaged in a small & rugged format and designed for outside broadcast, theatre and location applications. The AoIP22 is designed to easily and quickly interface existing analogue equipment to a Dante® / AES67 network audio system. Being powered by PoE means that only one cable needs to be connected to the network to carry both audio and power, providing flexibility and saving time on installation. Robust proven construction techniques, simple reliable interface and excellent specification will help make your technician’s life hassle free. Whilst the low cost and long asset life will keep the accountant satisfied.

The Radial DiNET™ DAN-TX2™ transmitter is an expanded versions of the DAN-TX Dante interface. The Radial DiNET™ DAN-TX2™ transmitter is an expanded versions of the DAN-TX Dante interface. Featuring Neutrik Ethercon connectors demanded by professional touring clients, both boxes deliver 24bit/96kHz resolution across any network using the Dante protocol. The DAN-TX2 features XLR combo, RCA, and 3.5mm analog inputs, with separate trim controls for both channels. 

The Radial DiNET™ DAN-RX2™ receiver is an expanded version of the DAN-RX Dante interfaces. Featuring Neutrik Ethercon connectors demanded by professional touring clients, both boxes deliver 24bit/96kHz resolution across any network using the Dante protocol. The DAN-RX2 is a 2-channel endpoint device, with Ethercon network input and XLR outputs. It also includes a powerful headphone amplifier with both ¼” and 3.5mm outputs.

The Synapse D32o is a Dante™/AES67 networked audio interface with 32 line level analog outputs. Features

• 32 line level balanced outputs with front panel for network level control
• Pair with the Synapse D32i for high quality network audio signal extension, or driving large racks of analog input amplifiers
• Software controllable output matrix routing
• Supports Dante™-AES67 Interoperablity Mode for universal network audio compatibility with virtually any networked DSP or mixing console
• Easily assignable front panel headphone access, volume control and source selection - includes local input and Dante™ monitoring modes
• Integrated power supply with optional external supply for applications  requiring redundant power requirements
• Configurable Dante™ interface for redundant or switched operation
• Integrated SFP ports for direct connection to fiber for long haul signal extension applications
• SFP Ports can double as switched connections in both redundant and switched operation to minimize the need for external network switches

The Synapse DM1 is a Dante™/AES67 Rackmount audio monitor. Features

• Supports easy monitoring of 32 Dante™ channels in standard monitoring mode and 128 subscription based monitoring channels in extended mode
• Transmits local analog audio channels and selected monitor audio channel to Dante™
• Supports Dante™-AES67 Interoperablity Mode
• Easily assignable front panel headphone and integrated speakers for confidence monitoring applications.
• Integrated power supply with optional external supply for applications  requiring redundant power requirements
• Integrated SFP ports for direct connection to fiber for long haul signal extension applications
• SFP Ports can double as switched connections in both redundant and switched operation to minimize the need for external network switches

The Synapse D16Mio is a 16 Channel I/O 1RU Dante™ / AES67 interface. Features

• 16 studio-grade mic preamps with line level capability as well
• Front panel network control of mic preamp gain, phantom power, mic/line input sensitivity
• 16 line level balanced outputs with front panel or network level control
• Useful for studio, live, rental and fixed installations requiring high numbers of high quality audio I/O
• Supports Dante™-AES67 Interoperablity Mode
• 16/24 bit, 44.1/48/88.2/96 kHz analog to Dante™ conversion
• Easily assignable front panel headphone access, volume control and source selection - includes local input and Dante™ monitoring modes
• Integrated power supply with optional external supply for applications  requiring redundant power requirements
• Integrated SFP ports for direct connection to fiber for long haul signal extension applications

Crown Audio's DCi 4|300DA is a four-channel, 300W Power Amplifier with Dante™ / AES67 Networked Audio, 2/4/8Ω and 70V/100V. Crown Audio's DCi 4|300DA is a four-channel, 300W Power Amplifier with Dante™ / AES67 Networked Audio, 2/4/8Ω and 70V/100V. For applications that require Dante or AES67 networked audio, the Crown DriveCore Install DA Series provides a balanced combination of output power, channel count and speaker load flexibility along with proprietary DriveCore® technology for superb efficiency and exemplary audio quality. The DCi DA Series includes a high-powered DSP with JBL speaker tunings, network control/monitoring, and the ability to drive 2/4/8/16 ohm, 70V and 100V speaker loads. The amp’s advanced capabilities and support for Dante Domain Manager makes it perfect for installations that have standardized on Dante for networked audio transport.

Crown Audio's DCi 4|600DA is a four-channel, 600W Power Amplifier with Dante™ / AES67 Networked Audio, 2/4/8Ω and 70V/100V. Crown Audio's DCi 4|600DA is a four-channel, 600W Power Amplifier with Dante™ / AES67 Networked Audio, 2/4/8Ω and 70V/100V. For applications that require Dante or AES67 networked audio, the Crown DriveCore Install DA Series provides a balanced combination of output power, channel count and speaker load flexibility along with proprietary DriveCore® technology for superb efficiency and exemplary audio quality. The DCi DA Series includes a high-powered DSP with JBL speaker tunings, network control/monitoring, and the ability to drive 2/4/8/16 ohm, 70V and 100V speaker loads. The amp’s advanced capabilities and support for Dante Domain Manager makes it perfect for installations that have standardized on Dante for networked audio transport.

Dynacord's TGX10 is a 4-channel DSP amplifier for live applications. Dynacord's TGX10 is a 4-channel DSP amplifier for live applications.

• Power density of up to 10kW in 2RU
• Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
• OMNEO integration for seamless compatibility with Dante and OCA
• Full color touch screen for control without software

Dynacord's TGX10 is a 4-channel DSP amplifier for live applications. Dynacord's TGX10 is a 4-channel DSP amplifier for live applications.

• Market-leading power density with up to 20kW in 2RU
• Fully integrated DSP with advanced 96 kHz processing and FIR Drive technology
• OMNEO integration for seamless compatibility with Dante and OCA
• Full color touch screen for control without software

RideAmp is a high-powered audio amplifier that is purpose-built for on-board applications like dark rides, coasters, trams, and parades. RideAmp is a high-powered audio amplifier that is purpose-built for on-board applications like dark rides, coasters, trams, and parades.  At Alcorn McBride, we are dedicated to creating tools that enable attraction designers to completely immerse guests in the themed world that they have envisioned.  When it comes to high-profile attractions, ride vehicles with on-board audio systems often play a key role in this vision. RideAmp is the industry’s first high-powered audio amplifier that has been specifically designed for vehicles used in themed attractions.  It provides 4-channels of amplification capable of delivering a formidable 350W of output power per channel.  Want to breath a little extra life into those large subwoofers or bass transducers?  Simply bridge outputs to achieve up to 700W of bone-crunching output power. When combined with the incredible capabilities of RidePlayer, RideAmp delivers features never before seen in a vehicle amplifier.  This includes Dante/AES67 network audio input for all-digital signal distribution, protecting your audio experience from the electrical noise introduced by the motors and actuators in the vehicle.  This same connection also enables intelligent control and status monitoring, allowing you to report the health of the entire on-board audio system to maintenance staff without requiring direct access the vehicle. RideAmp delivers the performance and quality of a professional amplifier from a compact and rugged package that’s tough enough to survive a coaster.  Vibration-resistant design, efficient DC power input, locking gain knobs, rugged connectors, and flexible mounting options make this product ideal for even the toughest on-board audio applications.

The DM8-Dante is a Dante Expansion Module with 16 x 32 Channels, Additional ULTRANET Audio Networking and Ethernet Connectivity

• Dante* expansion module for KLARK TEKNIK DM8000 etc. featuring Dante and ULTRANET audio networking
• Expands the processing benefits of DM8000 to third-party systems
• Dante enabled audio networking enables up to 16 input and 16 output channels
• ULTRANET digital audio networking for additional and simultaneous 16 output channels
• Full software configuration and control via integrated Ethernet port
• Dual RJ-45 connections for Dante primary and secondary networking interface
• Transformer-isolated design to eliminate ground loop interference
• 10-Year Warranty Program*
• Designed and engineered in the U.K.

The Kevic KS-1082P is an 8" 2WAY active network powered speaker with Dante. The Kevic KS-1082P is an 8" 2WAY active network powered speaker with Dante. Features:

• 8" powered speaker
• Lossless & Noiseless System by Dante Ethernet Transmission
• Optimization preset value apply by DSP
• Maximization of damping factor by D-Class power amplifier
• Ultralight voice coil and top class material are applied
• Simple system with DSP and power amplifier
• Can use as wedge monitor speaker