Dante-enabled Product Catalog

The BRIDGE B3 is an intelligent gateway between AES/EBU digital audio and AES67/Dante™ synchronous audio-over-IP streams. In your infrastructure, the BRIDGE B3 is the ideal solution to connect any digital audio equipment with your Audio-over-IP studio. The BRIDGE B3 is an intelligent gateway between AES/EBU digital audio and AES67/Dante™ synchronous audio-over-IP streams. In your infrastructure, the BRIDGE B3 is the ideal solution to connect any digital audio equipment with your Audio-over-IP studio. Thanks to its redundancy, the BRIDGE B3 can also provide secure distribution of your critical AES/EBU streams on any Dante redundant network.

• Stainless steel 1U chassis power consumption <50 W
• Front panel control interface for rapid overview of current status
• Dual AC/DC power supply 4 configurable GPIOs Wordclock synchronisation 24-bit audio routing: 44.1 kHz to 96 kHz
• AES67/Dante interface: 64-in/64-out EtherCON connector AoIP stream redundancy Integrated 4-port switch
• AES/EBU interface: 16-in/16-out mono Wordclock synchronisation and SRC (sample rate conversion) on each input

The IF-DA2 is a Dante interface card for Solid State Recorders SS-R250N/SS-CDR250N. Connection with 2 inputs and 2 outputs by mounting the IF-DA2 to the SS-R250N/SS-CDR250N for a Dante system. The IF-DA2 is a Dante interface card for Solid State Recorders SS-R250N/SS-CDR250N. Connection with 2 inputs and 2 outputs by mounting the IF-DA2 to the SS-R250N/SS-CDR250N for a Dante system.

The Octadrive DSP-DN has integral 32-bit audio digital processing and a bi-directional DANTE™interface. The Octadrive DSP-DN has integral 32-bit audio digital processing and a bi-directional DANTE™interface. The unit may thus act as an audio Analogue break-in function/distribution amplifier with the added advantage of highly configurable on-board signal processing, or form part of a DANTE™ based audio system, with all inputs and outputs being in the digital domain. In this case, the analogue connectivity can be used as an emergency backup signal path, in the event of failure of the digital audio sources The DSP (Digital Signal Processing) allows control of gain, EQ and delay for each input and output. Control of the DSP functions are via AXYS’s WinControl software, which uses DANTE™ control data capacity for communications.

The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems.  The PB-400-DN Industry amplifier is an ultra-reliable, high-power, 4 channel (250W per channel) audio power amplifier designed for use in critical systems. It is designed to drive 100 V line loudspeaker systems and is equipped with on-board DSP allowing gain, EQ, delay and other parameters to be controlled from a remote location using WinControl software, via DANTE™. The amplifiers are fully monitored, with automatic fault detection and reporting. Inputs may be either balanced analogue audio or digital audio via DANTE™. When used in conjunction with Duran Audio’s OpSTImizer® service the PB amplifiers can provide significant improvements in speech intelligibility within a tunnel.

The PB-800-DN Industry amplifier is an ultra-reliable, high-power, 8 channel (100W per channel) audio power amplifier designed for use in critical systems.  The PB-800-DN Industry amplifier is an ultra-reliable, high-power, 8 channel (100W per channel) audio power amplifier designed for use in critical systems. It is designed to drive 100 V line loudspeaker systems and is equipped with on-board DSP allowing gain, EQ, delay and other parameters to be controlled from a remote location using WinControl software, via DANTE™. The amplifiers are fully monitored, with automatic fault detection and reporting. Inputs may be either balanced analogue audio or digital audio DANTE™. When used in conjunction with Duran Audio’s OpSTImizer® service the PB amplifiers can provide significant improvements in speech intelligibility within a tunnel.

This ruggedized handy box lets you connect your legacy audio gear to the Dante™ world. It works both as a ramp-on device to convert an analog LINE signal into a Dante™ signal and as a ramp-off box to come out of the Dante™ network with an anlog signal. Both can happen siumultaneously! The NA2-IO-DLINE is an end-of-network device. It is a breakout box which allows two channels of audio to be integrated into a Dante™ network. Simultaneously, NA2-IO-DLINE converts a Dante™ stream into analog audio signals. Hence, it is possible to use this tiny box to feed analog audio signals into the Dante™ network while at the same time receiving a mix from another Dante™ source. NA2-IO-DLINE is designed for harsh stage conditions. It therefore features lockable chassis connectors for both the audio and network connections. For fixed installations, the rubber protection can be removed. With optional mounting brackets or a rack panel, the box can be mounted below tables, in floor boxes, or in equipment racks.

The third generation of Sony's acclaimed DWX series, this high performance digital wireless receiver is an ideal choice for live sound applications including theatre and concerts, as well as studio based TV production and EFP. The third generation of Sony's acclaimed DWX series, this high performance digital wireless receiver is an ideal choice for live sound applications including theatre and concerts, as well as studio based TV production and EFP. The two-channel 1U rack-mountable wireless receiver features Sony's advanced digital audio processing, encryption and RF transmission technologies to assure secure, stable transmission and reception of very high quality audio with low latency. The DWR-R03D is ideal for use in large-scale multi-channel productions, supporting up to 21 simultaneous channels per 8MHz TV band. Support for the Dante® audio-over-IP standard enables networked multi-channel operation. The DWR-R03D is compatible with Sony Wireless Studio control software for PC (Ver 5.0 or later) and the Wireless Studio Mobile smartphone app, allowing flexible remote operation. Remote control of up to 82 transmitters is possible using the Cross Remote™ function combined with the RMU-01 remote control unit (available separately). Components

• ECM-77LM 
• DWT-B03R

The TASCAM ML-32D is a professional Dante-focused converter made specifically to insert or extract analog audio into or out of a Dante network using external breakout devices that utilize Sub-D format connectors. The TASCAM ML-32D is a professional Dante-focused converter made specifically to insert or extract analog audio into or out of a Dante network using external breakout devices that utilize Sub-D format connectors. A poweful and flexible solution, the TASCAM ML-32D has 4 D-Sub intputs and 4 D-Sub outputs, whch can easiy be connected to any of the many devices that utilize D-Sub connectors such as microphone preamplifiers, large and small format console mixers, audio interfaces, amplifiers, and euro block connector devices. This simple, yet elegant, solution enables audio to be quickly and easily inserted into - or extracted from - the Dante audio stream.

The TASCAM ML-16D is a professional Dante-focused converter made specifically to insert or extract analog audio into or out of a Dante network using external breakout devices that utilize Sub-D format connectors. The TASCAM ML-16D is a professional Dante-focused converter made specifically to insert or extract analog audio into or out of a Dante network using external breakout devices that utilize Sub-D format connectors. A poweful and flexible solution, the TASCAM ML-316D has 2 D-Sub intputs and 2 D-Sub outputs, whch can easiy be connected to any of the many devices that utilize D-Sub connectors such as microphone preamplifiers, large and small format console mixers, audio interfaces, amplifiers, and euro block connector devices. This simple, yet elegant, solution enables audio to be quickly and easily inserted into - or extracted from - the Dante audio stream.

The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. As the LINUS14D is capable of powering every loudspeaker in the CODA catalogue, the M-RACK makes every smaller portable CODA system as clean and flawless in terms of aesthetics and connectivity as it is in terms of system performance. This ready-made factory solution is fully compatible with the larger LINUS-T-Rack allowing for easy cross rental and system expansion.

• One LINUS14D amplifier in a 3U case
• Delivers 4x 3500W @ 4 Ohm
• Requires only 16A / 230V (or 32A / 110V)
• Selectable inputs: Analog, AES over Ethernet, LiNET, DANTE
• Outputs on NL4, NL8
• 5-pol XLR comparator inputs for use with Coda Audio sensor controlled subwoofers
• All connectors at the front for easy workflow
• Sliding door for quick access
• Protection grill on the rear for connectors protection
• Can drive all CODA loudspeaker systems
• Fully compatible to LINUS T-RACK

The LINUS14D is a four channel DSP, Network, Comparator and Amplifier delivering 4x 3500W of clean power in a light weight 19”/2U package. The LINUS14D is a four channel DSP, Network, Comparator and Amplifier delivering 4x 3500W of clean power in a light weight 19”/2U package. The 4 audio inputs are selectable from Analog, LiNET digital audio or DANTE audio network and are routable to any of the 4 outputs via the input matrix. LINUS14D ENGINE – the class D-IC output stage topology delivers audiophile sonic accuracy with enormous headroom providing significant improvement of the system performance in dynamics and transparency. LINUS CORE – the SHARC floating point DSP processor ensures tremendous processing power enabling the integration of sophisticated audio algorithms. The advanced signal processing includes IIR and phase linear FIR filters for perfect linearity and superior sound performance as well as advanced look-ahead and frequency dependent limiters for increased system headroom and sonic fidelity under heavy use conditions. LiNET – is a robust, redundant audio transport solution that transmits digital audio over a standard CAT5 cable. Up to 8 digital audio signals can be sent to each amplifier via LiNET, buffered and sent to the next unit via the LiNET link out for daisy chaining. The signal routing inside the LINUS14D can be done remotely or using the pushbuttons on the front panel. DANTE – transmit digital audio over an Ethernet based network. COMPARATOR – the LINUS14D provides integrated feedback loop control for sensor controlled subwoofers. The unit has four sensor inputs connected to two 5-pol Neutrik XLR input. The comparator’s electronic circuit loop measures the voice coil movement and adjusts the amplifier driving voltage and/or current to correct any driver inaccuracy. It is a closed feedback-loop and therefore self-optimizing system in which the driver confirms precisely the power it needs to produce exactly the original audio signal. The key advantage is a very extended and controlled response. Any distortion produced by the driver or the enclosure is instantly corrected by the feedback. AUX – integrated evacuation massage contact in accordance with DIN EN 60849. LINUS LIVE – Ethernet based graphical user interface for fast and flexible system configuration, tuning and control. APPLICATIONS Containing factory presets for all CODA Audio loudspeaker systems LINUS14D offers a flexible solution for touring, permanent installation, corporate AV and portable applications.

The Duecanali 1604 is designed to work with lo-Z (from 2 Ω ) and with 70V/100V distributed lines: any mixed impedance output loads can be realized. Providing access to all functions yet easily set up, the Duecanali Series is versatile in use. Powersoft's legendary efficency saves valuable energy, keeping both operational cost and ‘carbon footprint’ at a minimum. The Duecanali 1604 is designed to work with lo-Z (from 2 Ω ) and with 70V/100V distributed lines: any mixed impedance output loads can be realized. A fully integrated state-of-the-art DSP yields extensive system management functionality. In addition to sound shaping and limiter functions in unique Powersoft style, the DSP hardware and Armonía Pro Audio Suite™ software enable compliance with IEC 60849 for the crucial requirements of sound systems for emergency purposes.

Speaking the language of the interpreter is what the DICENTIS Interpreter desk is designed to do. By observing and interviewing expert interpreters and technicians worldwide, the desk has been optimized for the real-life needs of interpreters.  Speaking the language of the interpreter is what the DICENTIS Interpreter desk is designed to do. By observing and interviewing expert interpreters and technicians worldwide, the desk has been optimized for the real-life needs of interpreters.  The DICENTIS Interpreter desk is part of the DICENTIS Conference System, which supports up to 100 interpreted languages. The conference system uses internationally recognized encryption standards for all audio and data. It offers the best protection against eavesdropping, unauthorized access and data tampering. High-quality, real-time audio and control is ensured by OMNEO* IP technology, which also allows for easy system integration with third-party solutions. OMNEO also enables the use of existing network infrastructure. The DICENTIS Interpreter desk is fully compatible with the DICENTIS platform and complies with the simultaneous interpreting equipment standard ISO 20109. It enables the creation of passive overflow rooms adjacent to the main meeting room in case there are more participants than can be accommodated at the main meeting location. Using the DICENTIS Meeting application, all languages and interpreter desks can be remotely configured and managed. 

The new Bosch Public Address and Voice Alarm System goes IP – PRAESENSA sets new industry benchmark. The new Bosch Public Address and Voice Alarm System goes IP – PRAESENSA sets new industry benchmark. All components of the system are networked, thereby ensuring the highest flexibility and scalability from small centralized to large decentralized systems. The Bosch OMNEO* IP architecture supports DanteTM audio networking, AES67 and AES70 protocol. The innovative multi-channel amplifier architecture with intelligent power allocation across the amplifier outputs and integrated spare channel significantly improves the effective utilization of available power, regardless of the loudspeaker load in each zone. As a result, fewer amplifiers are needed, saving up to 50 percent on space, energy and backup battery power and leading to a very competitive cost of ownership.  PRAESENSA offers special features for highest level of data security and full network link redundancy with smart integration of functions and backup facilities. No single point of failure is core to the system concept and only a few different devices are needed to fulfill all system and user needs. 

This product has reached "end of life" and is discontinued by the manufacturer The SL DI 4 XLR four input Dante preamp is the ideal interface for wireless microphone receivers, and adding mic/line inputs to a Dante system. The small form factor to the SL DI 4 XLR allows them to be mounted almost anywhere, putting them close to audio sources and minimizing interference-prone analog wiring. The SL DI 4 XLR features four balanced mic/line inputs, each with software selectable +48V phantom power and 8 gain levels. Front panel indicators show each channel’s gain and phantom power status for easy troubleshooting. The SL DI 4 XLR has two network connections to allow Dante Daisy Chaining. Dante Daisy Chaining further simplifies system infrastructure wiring by allowing multiple SL DI 4 XLRs to use a single CAT 5 home run connection to a network switch. Power can also be daisy chained. The SL DI 4 XLR is powered by either external +12VDC or any PoE network switch. All adjustable parameters, like mic/ line gain and phantom power, are software controlled.

Monacor's AKB-30DT/DSP is a Class D mono mixing amplifier with integrated Dante® module and DSP technology. Monacor's AKB-30DT/DSP is a Class D mono mixing amplifier with integrated Dante® module and DSP technology.

• 2 x mono 15 W/4-8 Ω
• Silent operation due to fanless cooling concept
• DSP can be controlled via MONACOR DSP software or via app
• Dante® input and feed-through output
• Speaker outputs via plug-in screw terminals
• Metal housing with mounting brackets
• Power is provided via PoE (Power over Ethernet) or optional 12 V power supply

Dynacord's IPX20:4 is a 4 x 5000 W multi-channel installation DSP amplifier. Dynacord's IPX20:4 is a 4 x 5000 W multi-channel installation DSP amplifier.

• 4 x 5000 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel drive mode with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier. Dynacord's IPX10:4 is a 4 x 2500 W multi-channel installation DSP amplifier.

• 4 x 2500 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX10:8 is a 8 x 1250 W multi-channel installation DSP amplifier. Dynacord's IPX10:8 is a 8 x 1250 W multi-channel installation DSP amplifier.

• 8 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dynacord's IPX5:4 is a 4 x 1250 W multi-channel installation DSP amplifier. Dynacord's IPX5:4 is a 4 x 1250 W multi-channel installation DSP amplifier.

• 4 x 1250 W multi-channel installation DSP amplifier with digitally controlled PFC supply
• Fully integrated DSP with high-resolution 96 kHz processing and FIR Drive
• Dante and OCA integration via OMNEO with fallback options
• Parallel, bridged and parallel-bridged drive modes with 70/100V and low impedance operation
• High efficiency Eco Rail technology for lower operating costs

Dante network digital audio adapters for the conversion of 2 Dante signal into 2 analogue line level signals and vice versa.

Pinanson offers two models:

1. Dante box D-A: for the conversion from 2 channel Dante signal (1 RJ-45 connector) into 2 channel analogue line level signal (2 XLR-3-M connectors).
2. Dante box A-D: for the conversion from 2 channel analogue line level signal (2 XLR-3-F connectors) into 2 channel Dante signal (1 RJ-45 connector).

Characteristics:

• The adapter is available in a MF box Pinanson format that is a mobile aluminium box format.
• Dante signal: for 44.1/48/96 KHz. 24 bits and 100 Mbps.
• Analogue signals: +4 dBu line level. Balanced signals.
• Power: PoE Class 1 802.3 af POE PD

The APB-D116 R-D is an active 19″ rack, AudioPressBox Drive Unit, 1 LINE Input, 1-channel Dante Interface, 16 Line/MIC Outputs, 1 buffered Output for up to 3 AudioPressBox expanders The APB-D116 R-D is an active 19″ rack, AudioPressBox Drive Unit, 1 LINE Input, 1-channel Dante Interface, 16 Line/MIC Outputs, 1 buffered Output for up to 3 AudioPressBox expanders. 1-channel active drive unit features 1 Analogue and DANTE input with high-quality digital-to-analogue converter. You can switch between Line or Dante input, depending on your needs. It offers 16 Line/MIC Level Outputs on the front and one output for expanders on the rear. Front outputs are balanced and individually transformer isolated with selectable output level for each output. You can expand the number of outputs with AudioPressBox expanders with up to 24 additional Line/MIC outputs per channel. As is AudioPressBox standard, you can use our signal processing like high-pass filter and compressor with limiter to achieve the perfect audio signal for all connected journalists. APB-Dante products uses Power over Ethernet (PoE). Power can be provided through the Ethernet cable from a PoE-capable network switch, or from a separate PoE injector. PoE Power Consumption: < 2 Watt 

The APB-D216 R-D is an active 19″ rack, AudioPressBox Drive Unit, 2 LINE Inputs, 2-channel Dante Interface, 16 Line/MIC Outputs, 2 buffered Outputs for up to 6 AudioPressBox expanders. The APB-D216 R-D is an active 19″ rack, AudioPressBox Drive Unit, 2 LINE Inputs, 2-channel Dante Interface, 16 Line/MIC Outputs, 2 buffered Outputs for up to 6 AudioPressBox expanders. 2-channel active drive unit features 2 Analogue DANTE inputs with high-quality digital-to-analogue converter. You can switch between Line or Dante input, depending on your needs. It offers 16 Line/MIC Level Outputs on the front and one output for expanders on the rear. Front outputs are balanced and individually transformer isolated with selectable output level for each output. You can expand the number of outputs with AudioPressBox expanders with up to 48 additional Line/MIC outputs per channel. As is AudioPressBox standard, you can use our signal processing like high-pass filter and compressor with limiter to achieve the perfect audio signal for all connected journalists. APB-Dante products uses Power over Ethernet (PoE). Power can be provided through the Ethernet cable from a PoE-capable network switch, or from a separate PoE injector.

A RIVAGE PM7 system is based around the CSD-R7 Digital Mixing Console with built-in signal processing for mixing and effects.  A RIVAGE PM7 system is based around the CSD-R7 Digital Mixing Console with built-in signal processing for mixing and effects. Other required components are one or more I/O racks for input and output, and a dedicated interface card for network connectivity. The RIVAGE PM7 system’s CSD-R7 Digital Mixing Console is the same size as the RIVAGE PM10 system CS-R10 Control Surface and has the same control layout. With built-in DSP it offers similarly high standards of operation and workflow efficiency in a relatively compact, portable system.

The Rio3224-D2 I/O rack is compatible with Yamaha CL and QL series consoles as well as the RIVAGE PM series. It features 32 analog inputs, 16 analog outputs, and eight digital AES/EBU outputs. The Rio3224-D2 I/O rack is compatible with Yamaha CL and QL series consoles as well as the RIVAGE PM series. It features 32 analog inputs, 16 analog outputs, and eight digital AES/EBU outputs. The Rio3224-D2 connects directly to Dante digital audio networks, allowing flexible system configuration. Dual power supply units are built in for high reliability, and a character/graphic display offers easy visual confirmation.

• 32 analog inputs and 16 outputs, and 8 digital outputs.
• Redundant connections are supported with primary and secondary connectors. Daisy chain connections are also supported.
• Comprehensive display and local control of gain and other parameters.
• Dimensions (WxHxD): 480 x 220 x 368mm (18.9" x 8.7" x 14.5")
• Net Weight: 13.5 kg (29.8 lbs)

The Rio1608-D2 is a high-performance I/O rack that features 16 analog inputs and 8 analog outputs, and is compatible with Yamaha CL and QL series consoles as well as the RIVAGE PM series.  The Rio1608-D2 is a high-performance I/O rack that features 16 analog inputs and 8 analog outputs, and is compatible with Yamaha CL and QL series consoles as well as the RIVAGE PM series. The Rio1608-D2 connects directly to Dante digital audio networks, allowing flexible system configuration. Dual power supply units are built in for high reliability, and a character/graphic display offers easy visual confirmation.

• 16 analog inputs and 8 outputs.
• Redundant connections are supported with primary and secondary connectors. Daisy chain connections are also supported.
• Comprehensive display and local control of gain and other parameters.
• Dimensions (WxHxD): 480 x 132 x 368mm (18.9" x 5.2" x 14.5")
• Net Weight: 9.6 kg (21.2 lbs)

The CSD-R7 Digital Mixing Console is the core component of any RIVAGE PM7 system, with 96 kHz processing, 120 monaural inputs, and a versatile complement of mixing busses (60 MIX, 24 MATRIX, and 2 STEREO).  The CSD-R7 Digital Mixing Console is the core component of any RIVAGE PM7 system, with 96 kHz processing, 120 monaural inputs, and a versatile complement of mixing busses (60 MIX, 24 MATRIX, and 2 STEREO). The console has three 12-faders bays for flexible setup and configuration, and dual power supply units are built in for enhanced reliability.

• Display: 15" touch panel x 2
• Faders: 38 (12+12+12+2)
• Selected Channel section: comprehensive channel parameters
• Custom Fader banks: 6 x 2 on each bay
• User Defined keys: 12 x 4 banks
• User Defined knobs: 4 x 4 banks
• Touch and Turn knobs: 2
• Analog I/O: 8 in / 8 out
• Slot: 3 HY slots, 2 MY slots
• AES/EBU: 4 in / 4 out (with SRC)
• Ports: GPI (8 in / 8 out), Word Clock In/Out, MIDI In/Out, 5 USB (1 for 2-track recording), Video Out (DVI-D), TC In
• Power supply: Dual redundant power supply built-in
• Dimensions (WxHxD): 1,549 x 417 x 848mm (61.0" x 16.4" x 33.4")
• Net Weight: 94 kg (207 lbs)