Voltera – D-2400-8


More Details

Similar Products

Crest_Audio_CKd_1204_Front_03611430
  • Crest Audio

Crest Audio – CKd 1204

The CKd Power Amplifiers combine the legendary overbuilt power supply design made famous by the Crest Audio Pro 200™ with NexSys® networking functionality and an ultra-lightweight class D topology. The design centers around an ultra-high efficiency amplifier output circuit that reduces weight while increasing output power, reliability and thermal efficiency. The CKd Series offers four multi-channel models to meet the needs of demanding audio installations. The CKd 1208 and CKd 1204 provide 1,250 Watts per channel in eight and four channels, respectively, while the CKd 608 and CKd 604 provide 625 Watts per channel in eight and four channels. Each amplifier channel will operate to rated power in direct 70-volt, 100-volt, 8-ohm or 4-ohm modes, configurable per channel. CKd amplifiers are networkable through Crest Audio’s Nx Dante-8™ and Nx Cobranet-8 NexSys control modules and either Crest Audio NexSys 5 or Peavey® MediaMatrix® NWare™ software programs for advanced control and audio routing. The Nx Dante-8 and Nx Cobranet-8 modules fit into the rear bay of CKd Series power amps and support all NexSys functions, DSP functions and Dante digital audio I/O (via 1 Gigabit Ethernet connection) or Cobranet digital audio I/O (via 100baseT connection). A Control Voltage input is included on each channel to allow external gain control, while the Fault output on each channel allows the CKd power amps to be wired to other monitoring systems. In addition, users can conserve energy by disabling channels that are not in use. The CKd Series includes Crest Audio's exclusive ACL™ (Active Clip Limiting), which automatically reduces gain at the onset of clipping to prevent amplifier and load damage, and IGM™ (Instantaneous Gain Modulation), which monitors load current to protect against overloading.
    Amplifiers
  • Dante Ch: 8x8
ashly-nXp-4002_600px|ashly-nXp-4002_600px
  • Ashly Audio

Ashly – nXp4002d

The nXp4002d is a 2 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 400W per channel at Low Z, 70V, and 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors are Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
  • Dante Ch: 4x4
  • 48kHz-96kHz
pema-4250-front|pema-4250-front|pema-4250-front|ne-4250-front
  • Ashly Audio

Ashly – pema4250d

Ashly's Pema™ is an energy efficient, Class-D amplifier topology with a switching power supply and full matrix mixer, translates to 80% energy efficient out of the box. The pema4250 is a 4-Channel @ 250 Watts per channel and ships with Ashly’s full Protea™ suite of DSP.

The pema4250d is also available in these models:

pema 4250.25d - pema Network Power Amp 4 x 250W @ 25V with 8x8 Protea DSP. Includes OPDante Card

pema 4250.70d - pema Network Power Amp 4 x 250W @ 70V with 8x8 Protea DSP. Includes OPDante Card

pema 4250.10d - pema Network Power Amp 4 x 250W @ 100V with 8x8 Protea DSP. Includes OPDante Card

    Amplifiers
  • Dante Ch: 8x8
  • 24-bit