Cart
← Back to Product Catalog

Williams Sound – DL207 NET D

Amplifiers

More details

Similar Products

atlas-sound-hpa2602_1200px|atlas-sound-hpa2602_1200px
  • AtlasIED

AtlasIED – HPA2602

The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The HPA is compact and lightweight in comparison to other models delivering the similar power levels. The HPA Series features generation II Class I Output topology that gives the efficiency close to a Class D amplifier with the sound quality of a Class AB amplifier. The power supply is switch mode global auto sensing gen 3 design that maintains a stable output during fluxuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any speaker load.The HPA Series features front panel detented level controls with a security cover, remote turn on, balanced inputs, fault reporting and an accessory card slot for an optional Dante™ 2-channel digital audio interface. Cooling is not an issue because of the unique output stage low resistance direct couple thermal transfer design. HPA also is energy efficient and meets Energy Starr standards with only drawing 1W of power in standby mode.Whether your application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the Atlas Sound HPA Series is the answer for high power/cost effective amplification needFeatures
  • 70.7V and 2Ω, 4Ω, and 8Ω Output Configurable
  • Balanced Inputs Euro Block Phoenix Style Connector
  • High Efficiency Fan Cooling
  • Remote Turn On
  • Accessory Card Slot for Optional Dante™ Digital Network Audio Card
  • Short-Circuit, Temperature, and DC Offset Protection
  • Soft Clip Limiter Protection
  • Stepped Attenuators with Security Covers
  • Stereo, Bridge, or Parallel Operating Modes Selectable via Rear Mounted Switch
  • Auto Sensing 120V/220V AC Mains Power Supply
  • Meets Energy Star Standards - 1W Standby Mode
    Amplifiers
  • Dante Ch: 2x0
  • 16-bit, 24-bit, 32-bit
See the product
revolution-acoustics-revnet-2140-d
  • Revolution Acoustics

Revolution Acoustics – RevNet 2140-D

The “Swiss Army Knife” of small amplifiers, the RevNet™ 2140-D gives you the power, versatility and quality you need for both commercial and high-end residential installations The “Swiss Army Knife” of small amplifiers, the RevNet™ 2140-D gives you the power, versatility and quality you need for both commercial and high-end residential installations. One RevNet amp will power two speakers. Units may be daisy-chained for larger applications, and the RevNet 2140-D has the added power of full Dante® compatibility with AES67 support. Quality Loads of headroom with 26 dB gain, coupled with the lowest distortion you’ll find on any comparable pro audio amp. Audiophile-quality RevNet amps are suitable for both pro audio and high-end HiFi operation. Powerful 140 watts per channel (280 W in mono) will power nearly any installed speaker in the room. RevNet amps can be used in 4/8/16 Ohm or 70/100V installations Easy to Install Fast-wiring Phoenix connectors allow you to quickly pre-wire sources and then just plug them into the amp. Versatile Control Direct RVC connections along with USB, TCP/IP, WiFi or Dante make it easy to manage your audio sources and volume. Onboard DSP for Easy Configuration A built-in sound masking generator allows you to quickly configure the amp for corporate uses, while 31 band EQ and RMS compressor bring you complete control over the sound of the room. Specifications
  • 2 x 140W@16/8/4 , 100V/70V @280W
  • Phoenix connectors for Inputs/Link Output, Amp Out and RVC
  • Dante® (with AES67 support) and USB interfaces along with Integrated WiFi for remote control and set up
  • Built-in sound masking generator
  • 31 band fully customizable DSP
  • In-Room AutoEQ and mobile app support
    Amplifiers
See the product
Ashly_-_nXe_752
  • Ashly Audio

Ashly – nXe752bd

Introducing our newest addition to the NX Series of Multi-mode Amplifiers: Now available in 150 & 75 Watts per channel housed in a 1U chassis. Multi-mode operation is standard on all nX amplifiers. Like it’s 2U models, choose from two or four channel configurations and set individual outputs to drive Low Impedance (2, 4, 8 Ohms), or 25V*, 70V, 100V Constant Voltage systems via rear-panel located DIP-switches. Add Ethernet (nXe) for monitoring and control, or add both Ethernet and Protea™ DSP (nXp). Expand onto a network with Dante™, CobraNet®, or AES3 digital inputs. Adapt Worldwide with a universal switch-mode power supply with PFC (Power Factor Correction). Reduce power consumption using Ashly EMS™ (Energy Management System) by triggering a sleep mode that draws <1W, which meets the most aggressive Energy Star® benchmark†. Follow pre-scheduled preset settings including levels and sources using RTC Event Scheduler (Real-Time Clock on nXe & nXp models). Remote Control ready via the Ashly Remote iPad® app, and/or hardwired Ashly remotes including analog (as well as serial) and Ethernet on nXe and nXp models. Monitor fault conditions and adapt via Ethernet and the onboard Fault Log included in nXe and nXp models.
    Amplifiers
  • Dante Ch: 4x0
See the product