Cart
← Back to Product Catalog

Bose – PowerMatch PM8500 / PM8500N

Amplifiers

More details

Similar Products

81849317_1259163634273815_828241351626719232_n
  • tm stagetec systems

tm stagetec systems – Network Amplifier Module (NAM)

The Network Amplifier Modules (NAM) is a high quality, highly versatile amplifier. With 4 versions available, 2 x Indoor Units and 2 x Outdoor Units, there is a NAM for almost any requirement.
Outdoor (IP66) units can be installed in the field near the location of the speakers for Railway Stations and other outdoor venues, whilst indoor NAMs can be installed neatly in the ceiling or on a wall inside.

There are two power options available with each standard power NAM having 4 x 12 Watt RMS class D amplifier channels and the High Power (NAM-HP), 4 x 50 Watt RMS class D amplifier channels, both units have an Ethernet switch and built in DSP (EQ, FIR, delay and gain). Each amplifier has an individual Dante input allowing for simple zoning and future changes.

    Amplifiers
See the product
nXp-1.52-front|nXp-1.52-front
  • Ashly Audio

Ashly – nXp1.52d

The nXp1.52d is a 2 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 1,500W per channel at Low Z and 70V modes, and 1,250W in 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors is Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
  • Dante Ch: 0x2
  • 48kHz-96kHz
See the product
listen-technologies-D10-2-DANTE_1200px|listen-technologies-D10-2-DANTE_1200px
  • Listen Technologies

Listen Technologies – D10-2 DANTE D Series MultiLoop™ Driver

The D10-2-DANTE (D Series) represents the global benchmark for digital audio hearing loop systems. The compact, elegant and sturdy units not only feature digital signal processing and networking functionality, but are also the most versatile and powerful solution available. The D10-2-DANTE (D Series) represents the global benchmark for digital audio hearing loop systems. The compact, elegant and sturdy units not only feature digital signal processing and networking functionality, but are also the most versatile and powerful solution available. The D10-2-DANTE digital amplifier is a 10 Amp dual output class 'D' driver; meaning a 60%+ increase in energy efficiency over existing solutions. Both drivers feature capacitive touch front panels with intuitive menus, built in test signals, and are fully networkable with a Wi-Fi accessible standard browser based control panel for remote set-up, monitoring and email alerts. Dante versions also feature a Dante specific RJ45 input for plug and play Dante network audio. The D10-2-DANTE features 10 Amps per loop output plus ample voltage headroom, making it the most flexible solution on the market, suitable for a huge range of applications. The added power of the D10-2-DANTE provides a solution for installations in environments containing very high levels of metal, previously not possible without the use of combiners. In another first for high-power Class D Induction Loop drivers, installation can be performed with total confidence, as unique multi-stage filtering ensures compatibility with both other system equipment and global EMC regulations. The D10-2-DANTE also boasts Dual Slope Metal Loss Control that caters to a wide range of metal loss frequency characteristics.
    Amplifiers
See the product