Cart
← Back to Product Catalog

NetPA U 4004 FX

Amplifiers

More Details

Similar Products

Bittner_Audio_4Xi_500x104
  • Bittner Audio

Bittner – 4X 2000i

The Bittner 4Xi power amplifier is available in 2 models, the 4X 1200i and 4X 2000i (with 4 x 1200 watt and 4 x 2000 watts @ 4 ohms respectively), and offers rear controls, analog or digital inputs, XLR or Phoenix input connectors, Speakon or Phoenix output connectors – the concept of the 4X is as flexible as its applications. Also available are audio networking via Dante™ and control via Ethernet (with SXL II) offering worldwide diagnostics and maintenance via the Internet The 4Xi and the front control version, the 4Xe, both offer the following specifications:
  • Up to 4x 2000 W in only 2 RU
  • Impedance measurement
  • Selectable Clip Limiter (hard/soft)
  • 4-channel Dante Inputs
  • SXL II Dataport (RS485)
  • High Tech SMT Design
  • Excellent sound and superior impulse response
  • 2 separate stereo amplifiers
  • Ready for 2 Ohm operation
  • Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
  • XLR inputs and Speakon outputs (e version)
  • Phoenix in- and outputs (i version)
  • High-End switched power supply with PFC
  • LED indicators for SIGNAL, CLIP, PROTECT, POWER
  • Temperature controlled, variable speed low noise fans
  • Digital wear-free Volume Controls (can be operated manually)
  • Selectable Stereo/Bridged Mode
  • Softstart
  • Sequential Remote Power On
  • 2 Alive Contacts
  • 3 Years Warranty
    Amplifiers
See the product
ied-DNA2404DL_1200px|ied-DNA2404DL_1200px
  • AtlasIED

AtlasIED – DNA2404DL

The DNA2404DL amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The DNA2404DL amplifier is an integral part of theAtlasIED GLOBALCOM® Communications System, allowing a few audio zones to be added where necessary when a full 16-zone T9160 amplifier frame is not required. The amplifier features Audinate's Dante™ digital audio input and four channels of 600 watt amplification. The DNA2404DL is controlled with network commands for selecting input routing and configuring EQ, delay and output levels. Amplifiers may be controlled by a stand-alone GLOBALCOM® configuration utility or through the GLOBALCOM System Management Center.The internal amplifier cards are Class D (switching mode) dual channel 600W amplifiers into the rated loads (70.7 Volts into 8Ω). Class D operation, combined with an integral switching mode power supply, offers many advantages, and the uniqueAtlasIED design makes full use of these benefits. They include higher efficiency, increased reliability, improved performance, and lower operating cost. Switching mode operation combined with high voltage power MOSFET devices make it possible to eliminate the heavy, costly, bulky transformers.AtlasIED’s design is stable under all load conditions (phase angles of 0 to 360 degrees). The amplifier card has 34dB of gain from its analog input to the loudspeaker output. Attenuation is handled ahead of the power amplifier by DSP controls through software.
    Amplifiers
See the product
  • Blustream

Blustream – NPA20DA

Our NPA20DA networked power amplifier delivers advanced audio integration within a commercial or residential AV installation. The NPA20DA features a 2 x 10W digital amplifier (1 x 20W mono) audio output and Dante® audio integration. The NPA20DA can be powered via PoE or PoE+ from a compatible network switch, or locally should the switch not support PoE. The unit also includes the ability to lower the amplifier power output subject to PoE capabilities, DSP with a 31 band EQ, audio delay for lip sync correction, and control via front panel, RS-232, TCP/IP, web-GUI or 12V trigger.
    Amplifiers
  • Dante Ch: 2x0
  • AES67 Enabled
See the product