Cart
← Back to Product Catalog

Lucky Tone – MA-XXXTD Series

Amplifiers

More details

Similar Products

POE-DANTE-AES67-Audio-Amplifiers-MNS-AMP30XXA-1P-1280X720-001-768x432
  • MONISMS

MONISMS – MNS-AMP30XXA-1P

The MONISMS Dante Audio Amplifier is a compact power amplifier module that drives small 4-8Ω speakers [Ceiling Speaker, In-wall Speaker, Pendant Speaker Column Speaker etc.] The MONISMS Dante Amplifier Power 30W, 4-8Ω load, This makes the module ideal for powering small areas consisting of only a few low power speakers.


The module's audio input is via an Ethernet audio network, allowing the use of the DANTE/ AES67 audio network protocol.
MNS-AMP30XXA-1P is powered by standard POE+ and has a MAX power of 30 watts. If there is not  POE+  used,  It can used the external 19VDC power supply.
Dante Audio Amplifier  can be mounted on a DIN rail or screwed onto a panel or wall for easy installation in a remote closet near the speaker area.

[Model:MNS-AMP3011A-1P] 1 Channel, 30W Output, [1 Pair Speaker Terminals].
[Model:MNS-AMP3012A-1P] 1 Channel, 2*15W Output, [2 Pairs Speaker Terminals].
[Model:MNS-AMP3022A-1P] 2 Channels, 2*15W Output, [2 Pairs Speaker Terminals].

    Amplifiers
See the product
panasonic-wp-dn360
  • Panasonic Connect

Panasonic – WP-DN360

The WP-DN360 is a digital amplifier with high efficiency and high reliability design.  The WP-DN360 is a digital amplifier with high efficiency and high reliability design. 
  • WP-DN 360 is 4 ch with maximum output 560 W × 4 (4 Ω load)
  • Due to the adoption of class D amplifier circuit and switching power supply, power loss is greatly reduced and space saving is realized. 
  • Equipped with a muting circuit to prevent pop noise when turning on / off the power switch. 
  • Overcurrent protection circuit that prevents overdrive in case of overload · output short circuit, equipped with overtemperature protection circuit to prevent abnormal heating of the power supply circuit · output circuit. 
  • Speaker protection circuit protects the speaker by cutting off the output when the output circuit fails. 
  • Equipped with protect indicator lights, inform the operating status of the protection circuit and system oscillation (when signals exceeding 20 kHz are continuously input). 
  • Corresponds to EIA rack mount. 
  • BTL (Bridged Trans- connect) connection that uses output of 2 ch as output of 1 ch can be used as a power amplifier of 1120 W × 2 (8 Ω load) with WP-DN 360.
    Amplifiers
See the product
avn-ah8-iso-300dpi
  • Sonifex

Sonifex – AVN-AH8

The AVN-AH8 multi-channel headphone amplifier is a 1U rack-mount which distributes 2 sets of stereo audio to up to 8 different sets of headphones, fed from the Dante AoIP network. A typical application might be to provide common headphone feeds for guests in a radio studio, coming directly from the AoIP network.

Each output has front panel unbalanced 1/4” & 3.5mm jack sockets and a rotary level control. The front panel potentiometers adjust the headphone volumes from mute (fully anticlockwise) to 0dB of gain when fully clockwise. This is useful if the Dante stream level is low or high and requires adjusting.

There are 8 parallel 1/4” jacks on the rear panel, for ease of wiring if the unit is installed in an enclosed rack.

Each of the 8 professional headphone outputs can each select between 2 stereo Dante sources which are routed via Dante controller. The level of each stereo Dante stream can be adjusted ±12dB using one of the two front panel rotary controls. The unit supports AES67 operation and is Dante Domain Manager compliant.

The AVN-AH8 front panel contains a power (PoE) LED, a DC LED, a network link status LED, and a clock LED. A recessed reset switch is also provided.

The unit is powered via Power over Ethernet (PoE) or a 12VDC input via a locking 2.5mm DC Input, 2A minimum rating.

    Amplifiers
  • Dante Ch: 4x0
  • 16-bit, 24-bit, 32-bit
See the product