Cart
← Back to Product Catalog

Linea Research – 44M10-DANTE

Amplifiers

More details

Similar Products

monisms-MNS-AMP30XX-2P
  • MONISMS

MONISMS – MNS-AMP30XXA-2P

The MONISMS Dante Audio Amplifier is a compact power amplifier module that drives small 4-8Ω speakers [Ceiling Speaker, In-wall Speaker, Pendant Speaker Column Speaker etc.] The MONISMS Dante Amplifier Power 30W, 4-8Ω load, This makes the module ideal for powering small areas consisting of only a few low power speakers.
The module's audio input is via an Ethernet audio network, allowing the use of the DANTE/ AES67 audio network protocol.


MNS-AMP30XXA-2P is powered by standard POE+ and has a MAX power of 30 watts. If there is not  POE+  used,  It can used the external 19VDC power supply.
Dante Audio Amplifier  can be mounted on a DIN rail or screwed onto a panel or wall for easy installation in a remote closet near the speaker area.

[Model:MNS-AMP3011A-2P] 1 Channel, 30W Output, [1 Pair Speaker Terminals].
[Model:MNS-AMP3012A-2P] 1 Channel, 2*15W Output, [2 Pairs Speaker Terminals].
[Model:MNS-AMP3022A-2P] 2 Channels, 2*15W Output, [2 Pairs Speaker Terminals].

    Amplifiers
See the product
nam2i-top-trans-small
  • r2p

r2p – Netspire NAM2i

The NetSpire™ NAM2i is an intelligent, network enabled amplifier. The device receives network digital audio and provides output to speakers using two integrated 12 watt Class D amplifiers, digital signal processing, and digital voice announcement.

The NetSpire™ NAM2i devices are housed in IP66 rated enclosures suitable for installation in harsh, outdoor, and rolling stock environments, where immunity from dust, water and physical deformation is required.

The NAM2i units integrate seamlessly with the NetSpire system and allow audio zones to be created anywhere a connection to the network is available. Each speaker is connected to an independent audio channel, and can be assigned to separate announcement zones or grouped in the same zone. The NAM2i can be configured to perform a different series of audio processing functions on each of the output channels. The 24bit DSP can perform the following configurable chains of audio processing functions on each channel:

  • Delay
  • Gain adjustments
  • Dynamic Range Compression & Expansion
  • Power Limiting
  • Parametric Frequency Equalisation

The NAM2i units also have a single balanced audio input which can be used to connect an Ambient Noise Sensing Microphone (ANC). The microphone is used to measure the ambient noise conditions of zone and adjust the volume of announcements automatically to compensate.

The NAM2i housing is IP66 rated, and encompassess the cable terminations on the NAM2i carrier bracket.

    Amplifiers
See the product
redx-sapphire-III-base|redx-sapphire-III-base
  • Redx

Redx – Sapphire III BASE

The Sapphire III is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. Sapphire III BASE is a four-channel audio power amplifier that provides 250W (4 ohms) output power per channel. It can also use bridge mode to provide 500W (8 ohm) two-channel output. Unlike Sapphire II, it adds the latest digital audio processing technology and support for Dante digital network audio transmission technology. It uses the latest SSA Technology and digital audio transmission and processing technologies to create:
  • PSM phase modulation technology, zero crossover distortion
  • Single-stage power conversion is equivalent to the direct use of AC mains power, which is one level lower than traditional class D power amplifiers.
  • Two-way energy recovery system to improve power conversion efficiency and effectively reduce the speaker coil voice temperature
  • ZVS, ZCS Soft Switch Technology, Significantly Reduces Switch Heat, Further Improves Conversion Efficiency
  • Overall efficiency up to 90% ultra high
In the past 100 years, the audio power amplifier topology has undergone Class-A, Class-AB, Class-D, etc., but it has always been a compromise between efficiency and sound quality. To date, SSA Technology has achieved Sapphire III BASE to Class-A sound quality levels with 90% overall system efficiency with its advanced and precise audio modulation technology, single stage power conversion, bidirectional energy recovery and soft switching technology. Really achieved "high efficiency and good voice!" Sapphire III BASE uses the latest digital audio processing and transmission technology, and targeted optimizations have been made. The efficient, reliable, and optimized application design, combined with its Class-A sound quality level, make it widely used in fixed installation systems.
    Amplifiers
See the product