Cart
← Back to Product Catalog

Hear Technologies – WSG Bridge

I/O Interfaces

More details

Similar Products

symetrix-xOut-4_1200px|symetrix-xOut-4_1200px
  • Symetrix

Symetrix – xOut 4

The cost effective xOut 4 increases a system’s analog output channel capacity resulting in a reduction in overall price per channel. The cost effective xOut 4 increases a system’s analog output channel capacity resulting in a reduction in overall price per channel. Designed exclusively for use with Dante-enabled Symetrix DSP units, each of the four analog outputs’ parameters (mute), along with bus assignments, are configured using Symetrix Composer open architecture software. xOut 4 set up is logical and fast with no requirement to use third party software; there are no mechanical switches or circuit board jumpers to set. Systems are simpler, cost less, and have fewer potential points of failure. A half-rack form factor conserves rack space, or, if preferred, the xOut 4 may be surface mounted. Features
  • Audio output (D/A) expander for systems that capitalizes on the surplus DSP of a Dante-enabled Symetrix DSP unit to bring overall system
  • costs down.
  • 4 line outputs with the industry leading performance specifications of Edge and Radius.
  • Configured with Symetrix Composer. No third party software, archaic DIP switches, or complicated front panel menus.
  • Network audio expansion using Dante protocol over standard IT networks. Ultra low latency.
  • Rack mount and surface mount kits sold separately.
    I/O Interfaces
  • Dante Ch: 4x4
  • 24-bit
See the product
NetBox32_Front
  • AEQ

AEQ – NetBOX 32 AD

NETBOX 32 AD interface features 32 input and 32 output channels organized in 16 mono analog + 8 stereo digital channels. The stereo digital audio channels can be configured as AES/EBU or SPDIF standard. It also incorporates 16 GPI and 16 GPO (each GPO connector includes a power supply pin to feed the output circuitry). NETBOX 32 AD interface features 32 input and 32 output channels organized in 16 mono analog + 8 stereo digital channels. The stereo digital audio channels can be configured as AES/EBU or SPDIF standard. It also incorporates 16 GPI and 16 GPO (each GPO connector includes a power supply pin to feed the output circuitry). Due to its high input and output capacity, it is especially suitable for central controls and link dispatches and also to increase or distribute the capacity of TDM BUS matrixes such as the AEQ BC 2000D.
    I/O Interfaces
See the product
neutrik-DANTE_Adapter-NA2-IO-DLINE|neutrik-DANTE_Adapter-NA2-IO-DLINE
  • Neutrik

Neutrik – NA2-IO-DLINE

This ruggedized handy box lets you connect your legacy audio gear to the Dante™ world. It works both as a ramp-on device to convert an analog LINE signal into a Dante™ signal and as a ramp-off box to come out of the Dante™ network with an anlog signal. Both can happen siumultaneously! The NA2-IO-DLINE is an end-of-network device. It is a breakout box which allows two channels of audio to be integrated into a Dante™ network. Simultaneously, NA2-IO-DLINE converts a Dante™ stream into analog audio signals. Hence, it is possible to use this tiny box to feed analog audio signals into the Dante™ network while at the same time receiving a mix from another Dante™ source. NA2-IO-DLINE is designed for harsh stage conditions. It therefore features lockable chassis connectors for both the audio and network connections. For fixed installations, the rubber protection can be removed. With optional mounting brackets or a rack panel, the box can be mounted below tables, in floor boxes, or in equipment racks.
    I/O Interfaces
  • Dante Ch: 2x2
  • 16-bit, 24-bit, 32-bit
See the product