Cart
← Back to Product Catalog

Auvitran – Ethernet to Optical Adapter

I/O Interfaces

More details

Similar Products

fp-nml2_400px
  • RDL

RDL – FP-NML2

The FP-NML2 is a high quality Dante network to mic/line interface that converts two Dante channels to two balanced outputs. Each output is individually switch-selectable to mic or line level. The FP-NML2 is ideal for adapting standard audio amplifiers or equipment to a Dante network. Model FP-NML2P operates from PoE. The FP-NML2 is a high quality Dante network to mic/line interface that converts two Dante channels to two balanced outputs. Each output is individually switch-selectable to mic or line level. The FP-NML2 is ideal for adapting standard audio power amplifiers, or other audio equipment, to a Dante network. Each line output provides +4 dBu balanced for a network digital audio level of -18 dBFS. Crosstalk is below the noise floor between all outputs across the entire audio spectrum. The noise floor is better than 80 dB below operating level with greater than 18 dB of headroom. The FP-NML2 operates from 24 Vdc and is available in a PoE version: FP-NML2P. If PoE power and an external 24 Vdc supply are both feeding an FP-NML2P, the unit will run from the external supply and will seamlessly switch over to PoE power upon loss of the external supply. 
    I/O Interfaces
See the product
Burl_B2_ADC_Dante_Front|Burl_B2_ADC_Dante_Front
  • Burl Audio

Burl – B2 Bomber ADC

The B2 Bomber analog to digital converter is designed to give you the ultimate in recording tone. BURL Audio designed an analog audio path that is complimentary to your mic pre and to the analog to digital process. By using a revolutionary hybrid circuit with a proprietary transformer, the BURL AUDIO BX1, and a discrete class-A, zero feedback, zero capacitor signal path, we have achieved dynamic and tonal balance. Features:
  • 44.1k Hz to 192k Hz, 24 bit, 2 channel ADC
  • Proprietary, high definition, BURL Audio BX1 transformer input
  • All class A, discrete transistors signal path with zero feedback, zero caps
  • Audiophile quality 6 position attenuator with standard headroom settings
  • High definition metering with simultaneous RMS and peak indication
  • Dante, 2 AES, SPDIF and Toslink output
  • BNC word clock input with two outputs of extremely low jitter clock
  • Frequency response at 48kHz sample rate is 12Hz to 22kHz, +/- 0.1dB
  • Frequency response at 96kHz sample rate is 15Hz to 46kHz, +/- 0.1dB
  • Frequency response at 192kHz sample rate is 18Hz to 94kHz, +/- 0.1dB
  • 120dB Dynamic Range (A- weighted), 117dB (no weighting)
  • -100dB THD+N (+4dBU = -15dBFs)
  • -94 dB THD+N (+18dBU = -1dBFs)
  • Rugged, Made in USA design
    I/O Interfaces
See the product
attero-tech-unD6IO|attero-tech-unD6IO
  • Attero Tech by Q-SYS

Attero Tech by Q-SYS – unD6IO

A 4-in, 2-Out I/O Interface that is a convenient, cost-effective way to add up to 6 channels of Dante audio to an existing Dante-based networked audio system. INPUTS - 2 XLR input with switchable mic/line gain and switchable phantom power on the inputs. Choice of unbalanced input (RCA or 3.5mm stereo jack) selectable by software. OUTPUTS - 1 3.5mm output, and two balanced outputs on a side‐mounted depluggable connector with software controlled volume. CONTROL - Audio flow assignment, input gain, phantom power and unbalanced input selection are all controllable via the Dante network connection.
    I/O Interfaces
  • Dante Ch: 2x4
  • 24-bit
See the product