Cart
← Back to Product Catalog

Stewart Audio – DSP100-2-CV

Amplifiers

More details

Similar Products

Crest_Audio_CKd_604_Front_03611450
  • Crest Audio

Crest Audio – CKd 604

The CKd Power Amplifiers combine the legendary overbuilt power supply design made famous by the Crest Audio Pro 200™ with NexSys® networking functionality and an ultra-lightweight class D topology. The design centers around an ultra-high efficiency amplifier output circuit that reduces weight while increasing output power, reliability and thermal efficiency. The CKd Series offers four multi-channel models to meet the needs of demanding audio installations. The CKd 1208 and CKd 1204 provide 1,250 Watts per channel in eight and four channels, respectively, while the CKd 608 and CKd 604 provide 625 Watts per channel in eight and four channels. Each amplifier channel will operate to rated power in direct 70-volt, 100-volt, 8-ohm or 4-ohm modes, configurable per channel. CKd amplifiers are networkable through Crest Audio’s Nx Dante-8™ and Nx Cobranet-8 NexSys control modules and either Crest Audio NexSys 5 or Peavey® MediaMatrix® NWare™ software programs for advanced control and audio routing. The Nx Dante-8 and Nx Cobranet-8 modules fit into the rear bay of CKd Series power amps and support all NexSys functions, DSP functions and Dante digital audio I/O (via 1 Gigabit Ethernet connection) or Cobranet digital audio I/O (via 100baseT connection). A Control Voltage input is included on each channel to allow external gain control, while the Fault output on each channel allows the CKd power amps to be wired to other monitoring systems. In addition, users can conserve energy by disabling channels that are not in use. The CKd Series includes Crest Audio's exclusive ACL™ (Active Clip Limiting), which automatically reduces gain at the onset of clipping to prevent amplifier and load damage, and IGM™ (Instantaneous Gain Modulation), which monitors load current to protect against overloading.
    Amplifiers
See the product
MNS-AMP230POE
  • MONISMS

MONISMS – MNS-AMP230POE

The MONISMS MNS-AMP230POE Dante Audio Amplifier is a compact power amplifier module that drives small 4-8Ω speakers (Ceiling Speaker, In-wall Speaker, Pendant Speaker Column Speaker etc.) The MONISMS MNS-AMP230POE Dante Audio Amplifier is a compact power amplifier module that drives small 4-8Ω speakers (Ceiling Speaker, In-wall Speaker, Pendant Speaker Column Speaker etc.) The MONISMS Dante Amplifier has two outputs, each with 15W of power into an 4-8Ω load. This makes the module ideal for powering small areas consisting of only a few low power speakers. The module's audio input is via an Ethernet audio network, allowing the use of the DANTE/ AES67 audio network protocol. MNS-AMP230POE is powered by standard POE+ and has a MAX power of 30 watts [2*15W]. If there is not  POE+  used,  It can used the external 24VDC power supply. Dante Audio Amplifier  can be mounted on a DIN rail or screwed onto a panel or wall for easy installation in a remote closet near the speaker area.
    Amplifiers
See the product
williams-sound-dl-210-sys-2_1200px
  • Williams AV

Williams Sound – DL210 SYS 2 2.0 D

Large-area, 48-volt induction loop system with network control, and installation wire and tape.  Large-area system offers flexible, powerful software control of mixing, equalization, compression and phase shift. Potent, class D, pulse-width amplifiers maximize efficiency and reduce size and weight. Dual-amplifier design offers the option of a single 12A output for large perimeter loops or dual 10A outputs for phase loop arrays. Dante Input. Large-area, 48-volt induction loop system with network control, and installation wire and tape.  Large-area system offers flexible, powerful software control of mixing, equalization, compression and phase shift. Potent, class D, pulse-width amplifiers maximize efficiency and reduce size and weight. Dual-amplifier design offers the option of a single 12A output for large perimeter loops or dual 10A outputs for phase loop arrays. Dante Input. System includes (1) DL210 NET D 2.0 induction loop amplifier (2) PLR BP1 body-pack receivers with batteries (2) EAR 022 surround earphones (1) BAT KT6 Dual Drop-in Charger Kit (includes CHG 3502 Dual Drop-In Charger and (2) BAT 026-2 AA NiMH batteries) (2) PLW F500 500 ft. rolls of flat power loop wire (6) FWT 001 rolls of flat wire warning tape (1) IDP 009 ADA Wall Plaque (T-Coil) 5-year Warranty on amplifier
    Amplifiers
See the product