Product Information
The PowerZone™ Connect 1U series is a line of DSP-enabled Class-D amplifiers designed to simplify the lives of system installers, providing unmatched reliability, efficiency, and exceptional system configuration.
Similar Products
- AtlasIED
AtlasIED – HPA2602
The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V/100V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads.
The AtlasIED High Power Amplifier “HPA” Series has been designed to be versatile for uses in both commercial 70V distributed systems and professional applications that require amplifiers to handle 4 and 2 ohm loads. The HPA is compact and lightweight in comparison to other models delivering the similar power levels. The HPA Series features generation II Class I Output topology that gives the efficiency close to a Class D amplifier with the sound quality of a Class AB amplifier. The power supply is switch mode global auto sensing gen 3 design that maintains a stable output during fluxuating power conditions. The power supply and output stage collectively are designed to deliver exceptional dynamic high output voltage and current to virtually any speaker load.The HPA Series features front panel detented level controls with a security cover, remote turn on, balanced inputs, fault reporting and an accessory card slot for an optional Dante™ 2-channel digital audio interface. Cooling is not an issue because of the unique output stage low resistance direct couple thermal transfer design. HPA also is energy efficient and meets Energy Starr standards with only drawing 1W of power in standby mode.Whether your application is a large distributed constant voltage sound system or a high SPL sound reinforcement system, the Atlas Sound HPA Series is the answer for high power/cost effective amplification needFeatures
- 70.7V and 2Ω, 4Ω, and 8Ω Output Configurable
- Balanced Inputs Euro Block Phoenix Style Connector
- High Efficiency Fan Cooling
- Remote Turn On
- Accessory Card Slot for Optional Dante™ Digital Network Audio Card
- Short-Circuit, Temperature, and DC Offset Protection
- Soft Clip Limiter Protection
- Stepped Attenuators with Security Covers
- Stereo, Bridge, or Parallel Operating Modes Selectable via Rear Mounted Switch
- Auto Sensing 120V/220V AC Mains Power Supply
- Meets Energy Star Standards - 1W Standby Mode
- Amplifiers
- Dante Ch: 2x0
- 16-bit, 24-bit, 32-bit
- Stewart Audio
Stewart Audio – MC850-CV-D
The MC850-CV-D is an 8 channel, 70/100V, 1RU amplifier delivering 50W per channel with channel-to-channel power sharing, Ethernet and RS-232 control. The MC850-CV-D amplifier supports Dante™ audio and has AES67 support.
The MC850-CV-D is an 8 channel, 70/100V, 1RU amplifier delivering 50W per channel with channel-to-channel power sharing, Ethernet and RS-232 control. The MC850-CV-D amplifier supports Dante™ audio and has AES67 support.
The MC850 family embodies the future of smart amplification with networked audio inputs, Ethernet configuration, control and reporting and flexible power allocation between channels. Whether it’s low impedance, 70V/100V or a mix of the two, there is a model for you with 8 channels and a total of 400W. Setup and configuration can be done anywhere with network access allowing the installer to locate in the zone for real time feedback. The software is simple, intuitive and targeted in scope to make set up easy and allow for granular control. There are 8 independent Dante™ inputs. The MC850 family is AES67 compatible. We built the MC850 family with the network in mind and you’ll find it shows.
• 8 independent Dante™ inputs
• Primary and Secondary Dante™ ports (redundant or switched)
• Ethernet port for control and reporting
• RS-232 control
• Power sharing up to 100W per channel
• Compact 1RU enclosure
• Made in USA
- Amplifiers
- Blustream
Blustream – NPA70DA
Our NPA70DA networked audio zone amplifier delivers advanced audio integration within a commercial or residential AV installation.
The NPA70DA features a 2 x 35W digital amplifier (1 x 70W mono) or 70V / 100V hi-level constant voltage output and Dante® audio integration.
The NPA70DA can be powered via PoE++ from a compatible network switch, or locally should the switch not support PoE++.
The unit also includes the ability to lower the amplifier power output subject to PoE capabilities, support for combined or independent LAN and Dante® connections, DSP with a 31 band EQ, audio delay for lip sync correction, and control via front panel, IR, RS-232, TCP/IP, web-GUI or 12V trigger.
- Amplifiers
- Dante Ch: 2x0
- AES67 Enabled