Leonis Cinema – SMA-OBIA


More details

Similar Products

CMX - Power amplifier with DSP & Dante
  • CMX

CMX – DSP-4500

The CMX DSP-4500 is a power amplifier with DSP and Dante.

  • 4 x 60W power amplifier
  • 100V, 70V, 4 Ohm & 8 Ohm output with selectors
  • Built-in DSP with EQ, gain control, crossover, delay, limiter, high-pass filter & low-cut filter
  • Dante network control with 4 In 4 Out matrix
  • Two Ethernet RJ-45 network connector for both Dante and DSP configure
  • Remote GPIO for failure outputs
  • 1U height 19” rack mount type power amplifier
  • Balanced line input by phoenix connector for four channels.
  • Each four inputs with separate gain control.
  • Separate four channel indicators for protection, clip, input and output.
  • Complete short circuit, overload, high temp, clip and DC protection.
  • Dante increases connectivity flexibility, and provides the freedom to use the amplifier power away from the source, wherever it is needed. It also enables the models to allow mixed inputs using either digital or onboard analog audio connections
    Amplifiers
  • Biamp

Voltera – D-2400-4M

Audio DSP and amplified loudspeaker controller; 4 channels sharing 2400W with Dante and AVB. Key Features
  • Powerful onboard DSP with ample headroom for large systems – the equivalent of a TesiraFORTÉ for Tesira custom processing and hosting of expanders
  • 4 class D channels sharing 2400 watts
  • Power sharing provides up to 75% of total power or 1800 W through any single channel
  • High peak voltage output capability: 160 Vpk
  • Each channel can drive low impedance (2.7, 4, 8, and 16 ohm), 70V, or 100V
  • Each model supports AVB, Dante, and AES67
  • Accurate raised cosine EQ for the entire frequency band
  • Group-controlled raised cosine EQ making it attractive for tuning large systems
  • Comprehensive amplifier limiter scheme avoids protective mutes and shutdowns
  • Processor can be sustained through POE – no main power required and no reboots
  • Support for failover-to-analog from networked audio input operation
  • 5-year warranty
  • Compliant with the US Trade Agreement Act (TAA)
  • Biamp Workplace Ready
    Amplifiers
  • Dante Ch: 32x32
  • 48kHz-96kHz
nXp-1.54-front|nXp-1.54-front
  • Ashly Audio

Ashly – nXp1.54d

The nXp1.54d is a 4 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 1,500W per channel at Low Z and 70V modes, and 1,250W in 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors is Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions shall include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
  • Dante Ch: 4x4
  • 24-bit