Lab.gruppen – FAD602


More details

Similar Products

coda-audio-linus-m-rack_1200px|coda-audio-linus-m-rack_1200px
  • Coda Audio

Coda Audio – LINUS M-Rack

The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. The LINUS M-RACK continues CODA Audio’s comprehensive system-based approach by providing a single LINUS14D DSP/amplifier with a CODA PAN-M connector panel in a compact 3U rack package. As the LINUS14D is capable of powering every loudspeaker in the CODA catalogue, the M-RACK makes every smaller portable CODA system as clean and flawless in terms of aesthetics and connectivity as it is in terms of system performance. This ready-made factory solution is fully compatible with the larger LINUS-T-Rack allowing for easy cross rental and system expansion.
  • One LINUS14D amplifier in a 3U case
  • Delivers 4x 3500W @ 4 Ohm
  • Requires only 16A / 230V (or 32A / 110V)
  • Selectable inputs: Analog, AES over Ethernet, LiNET, DANTE
  • Outputs on NL4, NL8
  • 5-pol XLR comparator inputs for use with Coda Audio sensor controlled subwoofers
  • All connectors at the front for easy workflow
  • Sliding door for quick access
  • Protection grill on the rear for connectors protection
  • Can drive all CODA loudspeaker systems
  • Fully compatible to LINUS T-RACK
    Amplifiers
Bittner_Audio_4Xe_500x108
  • Bittner Audio

Bittner – 4X 2000e

The Bittner 4Xe power amplifier is available in 2 models, the 4X 1200e and 4X 2000e (with 4 x 1200 watt and 4 x 2000 watts @ 4 ohms respectively), and offers front controls, analog or digital inputs, XLR or Phoenix input connectors, Speakon or Phoenix output connectors – the concept of the 4X is as flexible as its applications. Also available are audio networking via Dante™ and control via Ethernet (with SXL II) offering worldwide diagnostics and maintenance via the Internet The 4Xe and the rear control version, the 4Xi, both offer the following specifications:
  • Up to 4x 2000 W in only 2 RU
  • Impedance measurement
  • Selectable Clip Limiter (hard/soft)
  • 4-channel Dante Inputs
  • SXL II Dataport (RS485)
  • High Tech SMT Design
  • Excellent sound and superior impulse response
  • 2 separate stereo amplifiers
  • Ready for 2 Ohm operation
  • Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
  • XLR inputs and Speakon outputs (e version)
  • Phoenix in- and outputs (i version)
  • High-End switched power supply with PFC
  • LED indicators for SIGNAL, CLIP, PROTECT, POWER
  • Temperature controlled, variable speed low noise fans
  • Digital wear-free Volume Controls (can be operated manually)
  • Selectable Stereo/Bridged Mode
  • Softstart
  • Sequential Remote Power On
  • 2 Alive Contacts
  • 3 Years Warranty
    Amplifiers
stewart-audio-mc850
  • Stewart Audio

Stewart Audio – MC850-MXZ-D

The MC850-MXZ-D has 6 channels @ 70/100V, and 2 channels @ 4/8 Ohm. The 1RU amplifier delivers 50W per channel with channel-to-channel power sharing. The MC850-MXZ-D has 6 channels @ 70/100V, and 2 channels @ 4/8 Ohm. The 1RU amplifier delivers 50W per channel with channel-to-channel power sharing. It has Ethernet and RS-232 control. The MC850-MXZ-D amplifier supports Dante™ audio and has AES67 support. The MC850 family embodies the future of smart amplification with networked audio inputs, Ethernet configuration, control and reporting and flexible power allocation between channels. Whether it’s low impedance, 70V/100V or a mix of the two, there is a model for you with 8 channels and a total of 400W. Setup and configuration can be done anywhere with network access allowing the installer to locate in the zone for real time feedback. The software is simple, intuitive and targeted in scope to make set up easy and allow for granular control. There are 8 independent Dante™ inputs. The MC850 family is AES67 compatible. We built the MC850 family with the network in mind and you’ll find it shows.       
  • 8 independent Dante™ inputs
  • Primary and Secondary Dante™ ports (redundant or switched)
  • Ethernet port for control and reporting
  • RS-232 control
  • Power sharing up to 100W per channel
  • Compact 1RU enclosure
  • Made in USA
    Amplifiers