Cart
← Back to Product Catalog

Extron – NetPA U 1004-70V

Amplifiers

More details

Similar Products

stewart-audio-mc850
  • Stewart Audio

Stewart Audio – MC850-CV-D

The MC850-CV-D is an 8 channel, 70/100V, 1RU amplifier delivering 50W per channel with channel-to-channel power sharing, Ethernet and RS-232 control. The MC850-CV-D amplifier supports Dante™ audio and has AES67 support. The MC850-CV-D is an 8 channel, 70/100V, 1RU amplifier delivering 50W per channel with channel-to-channel power sharing, Ethernet and RS-232 control. The MC850-CV-D amplifier supports Dante™ audio and has AES67 support. The MC850 family embodies the future of smart amplification with networked audio inputs, Ethernet configuration, control and reporting and flexible power allocation between channels. Whether it’s low impedance, 70V/100V or a mix of the two, there is a model for you with 8 channels and a total of 400W. Setup and configuration can be done anywhere with network access allowing the installer to locate in the zone for real time feedback. The software is simple, intuitive and targeted in scope to make set up easy and allow for granular control. There are 8 independent Dante™ inputs. The MC850 family is AES67 compatible. We built the MC850 family with the network in mind and you’ll find it shows.        • 8 independent Dante™ inputs • Primary and Secondary Dante™ ports (redundant or switched) • Ethernet port for control and reporting • RS-232 control • Power sharing up to 100W per channel • Compact 1RU enclosure • Made in USA
    Amplifiers
See the product
ppa_1000
  • Four Audio

Four Audio – PPA 1000

The PPA series provides a high-quality DSP-powered amplifier solution for active loudspeakers. It features Pascal high-power modules, analog, digital and Dante inputs and is available in different configurations for various kinds of speakers.
    Amplifiers
See the product
ashly-nXp-8004_600px|ashly-nXp-8004_600px
  • Ashly Audio

Ashly – nXp8004d

The nXp8004d is a 4 channel multi-mode amplifier capable of driving 2 Ohm loads at full power. The maximum rated output power is 800W per channel at Low Z, 70V, and 100V mode. There is an automatic but defeatable sleep mode consuming <1W, and instant standby mode controlled by contact closure or software. A switch mode power supply auto-detects 120VAC or 240VAC mains, and a Neutrik® powerCON is used for the AC cord. Each channel has selectable output mode of Low Z, 70V, or 100V, an 80Hz high-pass filter, input limiter, and input gain settings of 26dB, 32dB, 38dB, or 1.4V. Each channel has remote DC level control. Input connectors are Neutrik® XLR/TRS combo jack and Euroblock, while output connectors are Neutrik® speakON. The unit has a front panel power switch and level controls that can be disabled. LEDs indicate Protect, Sleep, Disabled, Com, and Bridge mode status, as well as Temperature, Output Current, Output Signal, and Clipping/Mute status per channel. The unit has Ethernet control with a real-time clock for event scheduling. The unit has serial data remote control, aux preamp outputs, preset control, fault condition logic outputs, optional network audio and AES3 digital audio capability. The unit has 32-bit DSP processing at 48kHz or 96kHz sampling rate. DSP functions include swept load impedance, gain, dynamics including autoleveler and ambient noise compensation, equalization including graphic, parametric, feedback suppressor, and FIR filters, a matrix mixer including automixing, crossover, delay, and a signal generator. The amplifier has temperature dependent variable speed forced-air cooling.
    Amplifiers
  • Dante Ch: 4x0
  • 24-bit
See the product