Bose – ControlSpace EP22-D


More details

Similar Products

digigram-AUDIOWAY-bridge-B3_1200px_0
  • Digigram

Digigram – Audioway Bridge B2

The BRIDGE B2 is an intelligent gateway between MADI digital audio and AES67/Dante™ synchronous audio-over-IP streams. Forming the backbone of your infrastructure, the BRIDGE B2 is the ideal solution to distribute and interconnect your MADI and AES67/Dante mission-critical streams in the studio. The BRIDGE B2 is an intelligent gateway between MADI digital audio and AES67/Dante™ synchronous audio-over-IP streams. Forming the backbone of your infrastructure, the BRIDGE B2 is the ideal solution to distribute and interconnect your MADI and AES67/Dante mission-critical streams in the studio.
  • Stainless steel 1U chassis power consumption <50 W
  • Front panel control interface for rapid overview of current status
  • Dual AC/DC power supply 4 configurable GPIOs Wordclock synchronisation 24-bit audio routing: 44.1 kHz to 96 kHz
  • AES67/Dante interface: 64-in/64-out EtherCON connector AoIP stream redundancy Integrated 4-port switch
  • MADI interface: 1 x optical 64-in/64-out connector 1 x BNC 64-in/64-out connector
    I/O Interfaces
unika-NBB-04R_1200px|unika-NBB-04R_1200px
  • Unika

Unika – NBB-04R

The NBB-04R Networked Audio Receiver receives 4 channels of analog audio and converts them into Dante networked audio stream which in turn can be received by other Dante-enabled devices. It comes with two RJ-45 Ethernet ports and phantom power support, and can be powered by either PoE or 48V external power adapter. The NBB-04R Networked Audio Receiver receives 4 channels of analog audio and converts them into Dante networked audio stream which in turn can be received by other Dante-enabled devices. It comes with two RJ-45 Ethernet ports and phantom power support, and can be powered by either PoE or 48V external power adapter.
  • Dante-enabled networked Audio Receiver
  • Streaming audio in robust standard Ethernet cable (a.k.a., Digital Snake)
  • Easily organize and expand network topology with Ethernet switches
  • Uncompressed 24-bit PCM coding with sample rate up to 96KHz
  • Two RJ-45 ports make Daisy-chain cascading feasible
  • Powered by either PoE or 48V adapter
  • Gain or Attenuate control for each channel
  • Phantom power engagement control per channel
  • A signal clip indicator for all inputs
  • XLR Combo sockets for both XLR and phone plugging
  • Routing and other configuration are set with Dante Controller software
    I/O Interfaces
rts-omneo-oei-2|rts-omneo-oei-2
  • RTS

RTS – OEI-2

The OEI-2 enables connectivity between analogue audio sources and legacy RTS key panels and an OMNEO network. This allows users to maintain existing infrastructure and the equity of their original equipment investment while updating to high-performance OMNEO media networking architecture.
  • Provides an interface between legacy RTS key panels and RTS OMI OMNEO interface cards for ADAM and ADAM-M units.
  • Support for both USOC or 586B wiring.
  • Provides less than 20 ms of audio latency in typical network installations.
  • Provides a frequency response of 20 Hz to 20 KHz to the keypanel.
  • Supports DHCP and device discovery for easy set up and network management.
  • Optional fibre connection – multi-mode or single-mode available.
  • Supports CAT-5/5e and CAT-6 with dual Ethernet connectors for device looping.
  • Supports compatibility with third-party Dante™
    I/O Interfaces
  • AES67 Enabled