Cart
← Back to Product Catalog

AUDAC – PMQ480

Amplifiers

More details

Similar Products

301_T-rack_front_R-1200x900-1
  • Coda Audio

Coda Audio – LINUS T-RACK

3x LINUS14D amplifiers in a 10U heavy-duty rack Delivers 12x 3500 W @ 4 Ohm Integrated shock-mount suspension system for maximum protection Integrated rigging hardware for flown or ground stacked deployment Rear mounted power distribution (optional switchable: US / EU) Selectable inputs: Analog, AES over Ethernet, LiNET, DANTE Outputs on NL4, NL8 (Socapex optional available) 5-pin XLR comparator inputs for use with CODA Audio sensor controlled subwoofers All inputs and outputs are at the front for easy workflow Expandable – rack to rack internal cabling allows to join two or more racks together Sliding doors for quick access Protection grille on the rear Can drive all CODA loudspeaker systems Compatible to LINUS20, LINUS40 and M-RACK

    Amplifiers
  • Dante Ch: 8x0
See the product
adam-hall-DSP44K-proaudio_600px
  • Adam Hall Group

Adam Hall Group – LD Systems DSP 44 K ProAudio

Designed for the professional audio market, the LD Systems® DSP 44 K power amp was developed in cooperation with Ram Audio, whose products are sold in many countries by Adam Hall Group. Designed for the professional audio market, the LD Systems® DSP 44 K power amp was developed in cooperation with Ram Audio, whose products are sold in many countries by Adam Hall Group. This new powerhouse features a fully-integrated DANTE™ network, a high-performance DSP and controllability via USB and Ethernet using external control PC software. The top-of-the-line power amp can be operated as a two or four-channel device. An impressive four kilowatts provide plenty of power reserves as 4 x 1,000 watts at 4 or 2 ohms or 2 x 2,000 watts (bridge mode) at 8 or 4 ohms. Maximum operational reliability is also guaranteed at 2 ohms. Comprehensive safety features permanently protect the power amps and the system, even in tough situations. FIR/IIR filtering, EQs and crossovers, as well as delay functions, are all part of the overall technology.
    Amplifiers
  • 24-bit
  • 48kHz
See the product
ks_audio_ca__4d_front
  • KS Audio

KS Audio – CA 4D

The CA 4D is a 4 channel MOSFET amplifier with controller card system configuration technology, using digital controller cards D MOD or F MOD. Both exclusively supporting the KS AUDIO FIRTEC™ finite impulse response technology. When changing controller cards or when loading a new program from the internal memory both the inputs and the outputs are appropriately configured to reflect the correct set up.

Whether or not the system is configured as 4 single channels – 2 channel / 2 way – 2 channel with mono Sub woofer – 2 channel mono bridged high power sub woofer – 1 channel 3 way - L and R SAT configuration, nearly every combination of KS AUDIO speaker systems is possible. This allows for a wide field of application, from small and medium size concert sound reinforcement to speech reproducing at the highest quality.

The CA 4D is equipped with 4 independent analog FET power amp modules. Two of them deliver a continuous sinewave power of 700 watts into 4 ohms each. While the other two modules deliver half that power. The controller card and an applicable program determines the distribution of power to always deliver the maximum available. The high performance of the CA 4D amplifier is achieved by three balanced supply voltages. The power losses are substantially less than with any other conventional analog power-amplifier designs. A total of 40 quality selected power MOSFET transistors, deliver a maximum headroom. Soft clipping circuits working in conjunction with

the operating voltage, limit the NF signals and therefore enable the power amps to always work with a high damping factor as well as remaining fully regulated.

The power supply is a state-of-the-art, heavy duty wide-range switch mode design, with Power-Factor-Correction (PFC) built in. The start-up current is limited to assure maximum protection. A second power supply is used to independently supply the controller card electronics along with the low voltage cooling fans and to operate the stand-by switch. Excess temperature is dissipated by 2 fans. The air is taken in from the front panel inlet thru an easy to clean filter. It is passed through to the back panel outlet, while passing over the heat fins and the power transformer to cool these units down to nominal operating temperatures.

On the front panel there are 4 mute switches corresponding to the 4 channels of the amplifier. Each of these switches has a red LED below it to indicate the mute status. On the rear panel there are 4 Neutrik speakON output connectors. Their status is indicated by 4 green LEDs. The mains cable is connected via a PowerCon.

The housing is constructed of 1.5mm thick steel while the 19′′ front plate is constructed of 4mm thick anodized aluminum and has 2 handles for ease of use.

    Amplifiers
See the product