Cart
← Back to Product Catalog

Linea Research – 48M06-Dante

Amplifiers

More details

Similar Products

CMX - Power amplifier with DSP & Dante
  • CMX

CMX – DSP-4060

The CMX DSP-4060 is a power amplifier with DSP and Dante.

  • 4 x 60W power amplifier
  • 100V, 70V, 4 Ohm & 8 Ohm output with selectors
  • Built-in DSP with EQ, gain control, crossover, delay, limiter, high-pass filter & low-cut filter
  • Dante network control with 4 In 4 Out matrix
  • Two Ethernet RJ-45 network connector for both Dante and DSP configure
  • Remote GPIO for failure outputs
  • 1U height 19” rack mount type power amplifier
  • Balanced line input by phoenix connector for four channels.
  • Each four inputs with separate gain control.
  • Separate four channel indicators for protection, clip, input and output.
  • Complete short circuit, overload, high temp, clip and DC protection.
  • Dante increases connectivity flexibility, and provides the freedom to use the amplifier power away from the source, wherever it is needed. It also enables the models to allow mixed inputs using either digital or onboard analog audio connections
    Amplifiers
See the product
ne-8250-front|ne-8250-front|ne-8250-front
  • Ashly Audio

Ashly – ne8250bd

Designed around an energy efficient Class-D platform with a switching power supply, connecting and controlling an amplifier for networked systems is simplified with Ashly ne Amplifiers. The ne8250bd offer 8-Channels @ 250W per channel with separate hi-z and lo-z models. NE offers ease of use, setup and control using standard 10/100 Ethernet protocol and Protea™ ne Software. NE Series Amplifiers are offered in two separate platforms—the standard network amplifier or a network amplifier with an on-board Protea™ DSP Processor.

The ne8250 series contains these additional models:

  • ne8250.25bd - Network Power Amplifier 8 x 250W @ 25V. Includes OPDante & OPDAC-8 Cards
  • ne8250.70bd - Network Power Amplifier 8 x 250W @ 70V. Includes OPDante & OPDAC-8 Cards
  • ne8250.10bd - Network Power Amplifier 8 x 250W @100V. Includes OPDante & OPDAC-8 Cards
  • ne8250ped - Network Power Amplifier 8 x 250W @ 4 Ohms w/Protea DSP. Includes OPDante & OPDAC-8 Cards
  • ne8250.25ped - Network Power Amplifier 8 x 250W @ 25V w/Protea DSP. Includes OPDante & OPDAC-8 Cards
  • ne8250.70ped - Network Power Amplifier 8 x 250W @ 70V w/Protea DSP. Includes OPDante & OPDAC-8 Cards
  • ne8250.10ped - Network Power Amplifier 8 x 250W @ 100V w/Protea DSP. Includes OPDante & OPDAC-8 Cards
    Amplifiers
  • Dante Ch: 8x8
  • 24-bit
See the product
FLX80-4-70V
  • Stewart Audio

Stewart Audio – FLX80-4-CV-D

4 Channel DSP-Enabled Amplifier 4 x 80W @ 70/100V Dante™ Network Enabled The FLX-E-80-4-CV-D is a 4 channel, 70V/100V, 1/2 rack amplifier delivering 80W per channel with built in DSP, Ethernet control & reporting, secondary RS-232 control and remote volume control. The FLX-E-80-4-CV-D amplifier supports Dante™ audio.
  • Onboard DSP for signal routing and filtering
  • Ethernet configuration, control & reporting
  • Pre-mix level control
  • 4 analog inputs (4 line/mic; 2 w/ phantom power)
  • 4×4 Break in/Break out Dante™ channels
    Amplifiers
See the product